diff --git a/.gitignore b/.gitignore index 0c320bf..32a6b8c 100644 --- a/.gitignore +++ b/.gitignore @@ -112,3 +112,7 @@ all.config # Kdevelop4 *.kdev4 + +# dtb objects +*.dtb +*.dtbo diff --git b/Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr b/Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr new file mode 100644 index 0000000..e2df613 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr @@ -0,0 +1,63 @@ +What: /sys/devices/platform/bone_capemgr/slots +Date: May 2015 +KernelVersion: 4.0 +Contact: Pantelis Antoniou +Description: + READ: + Describe the state of all the slots of the beaglebone capemgr. + Each line of the output describes a slot: + The slot format is as following: + : [P-][F-][O-][l-][L-][D-] \ + ,, + , + + Where the flags are: + P: Slot has been probed + F: Slot has failed probing (i.e. no EEPROM detected) + O: Slot has been overridden by the user + l: Slot is current loading + L: Slot has completed loading and is ready + D: Slot has been disabled + + Example: + 0: P---L- -1 BeagleBone RS232 CAPE,00A1,Beagleboardtoys,BB-BONE-SERL-03 + 1: PF---- -1 + 2: PF---- -1 + 3: PF---- -1 + + WRITE: + Writing a string of the form [:version] issues a request to + load a firmware blob containing an overlay. The name of the firmware blob + is -[version|00A0].dtbo. This act is defined as a slot override. + + Writing a negative slot id removes the slot if it was an overridden one, or + unloads a slot that was probed. + +What: /sys/devices/platform/bone_capemgr/baseboard/ +Date: May 2015 +KernelVersion: 4.0 +Contact: Pantelis Antoniou +Description: Contains the probed base board EEPROM field; one of: + board-name - board-name as stored in cape EEPROM + dc-supplied - whether the cape draws or supplies DC + eeprom-format-revision - EEPROM format rev, only 00A0 supported + header - header; should be 'aa 55 33 ee' + manufacturer - manufacturer string + part-number - part-number of the cape + serial-number - serial number of the cape + version - version of the cape, i.e. 00A0 + number-of-pins - displayed but ignored + pin-usage - displayed but ignored + sys-5v - displayed but ignored + vdd-3v3exp - displayed but ignored + vdd-5v - displayed but ignored +What: /sys/devices/platform/bone_capemgr/slot-/ +Date: May 2015 +KernelVersion: 4.0 +Contact: Pantelis Antoniou +Description: Contains the probed cape's EEPROM field; the field is one of: + board-name - baseboard name i.e. A335BNLT + header - header; should be 'aa 55 33 ee' + revision - baseboard revision + serial-number - baseboard serial number + config-option - displayed but ignored diff --git b/Documentation/ABI/testing/sysfs-firmware-devicetree-overlays b/Documentation/ABI/testing/sysfs-firmware-devicetree-overlays new file mode 100644 index 0000000..88d1549 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-firmware-devicetree-overlays @@ -0,0 +1,52 @@ +What: /sys/firmware/devicetree/overlays/ +Date: October 2015 +Contact: Pantelis Antoniou +Description: + This directory contains the applied device tree overlays of + the running system, as directories of the overlay id. + +What: /sys/firmware/devicetree/overlays/enable +Date: October 2015 +Contact: Pantelis Antoniou +Description: + The master enable switch, by default is 1, and when + set to 0 it cannot be re-enabled for security reasons. + + The discussion about this switch takes place in: + http://comments.gmane.org/gmane.linux.drivers.devicetree/101871 + + Kees Cook: + "Coming from the perspective of drawing a bright line between + kernel and the root user (which tends to start with disabling + kernel module loading), I would say that there at least needs + to be a high-level one-way "off" switch for the interface so + that systems that have this interface can choose to turn it off + during initial boot, etc." + +What: /sys/firmware/devicetree/overlays/ +Date: October 2015 +Contact: Pantelis Antoniou +Description: + Each directory represents an applied overlay, containing + the following attribute files. + +What: /sys/firmware/devicetree/overlays//can_remove +Date: October 2015 +Contact: Pantelis Antoniou +Description: + The attribute set to 1 means that the overlay can be removed, + while 0 means that the overlay is being overlapped therefore + removal is prohibited. + +What: /sys/firmware/devicetree/overlays/// +Date: October 2015 +Contact: Pantelis Antoniou +Description: + Each of these directories contain information about of the + particular overlay fragment. + +What: /sys/firmware/devicetree/overlays///target +Date: October 2015 +Contact: Pantelis Antoniou +Description: + The full-path of the target of the fragment diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 94b57f2..413aeed 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -24,6 +24,8 @@ Optional properties: - ti,no-reset-on-init: When present, the module should not be reset at init - ti,no-idle-on-init: When present, the module should not be idled at init - ti,no-idle: When present, the module is never allowed to idle. +- ti,deassert-hard-reset: list of hwmod and hardware reset line name pairs + (ascii strings) to be deasserted upon device instantiation. Example: diff --git b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt new file mode 100644 index 0000000..f719b2d --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt @@ -0,0 +1,89 @@ +Bindings for TI's CPUFreq driver +================================ + +The ti-cpufreq driver works with the operating-points-v2 binding described +at [../opp/opp.txt] to make sure the proper OPPs for a platform get enabled +and then creates a "cpufreq-dt" platform device to leverage the cpufreq-dt +driver described in [cpufreq-dt.txt]. + +Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx +families support different OPPs depending on the silicon variant in use. +The ti-cpufreq driver uses the revision and an efuse value from the SoC to +provide the OPP framework with supported hardware information. This is used +to determine which OPPs from the operating-points-v2 table get enabled. In +order to maintain backwards compatilibity if this information is not present +the "cpufreq-dt" platform device is still created to attempt to find an +operating-points (v1) table, otherwise no OPPs will be available because +safe OPPs cannot be determined. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use +- ti,syscon-efuse: Syscon phandle, offset to efuse register, efuse register + mask, and efuse register shift to get the relevant bits + that describe OPP availability +- ti,syscon-rev: Syscon and offset used to look up revision value on SoC + +In 'operating-points-v2' table: +- opp-supported-hw: Two bitfields indicating: + 1. Which revision of the SoC the OPP is supported by + 2. Which eFuse bits indicate this OPP is available + + A bitwise and is performed against these values and if any bit + matches, the OPP gets enabled. + +NOTE: Without the above, platform-device for "cpufreq-dt" is still created + but no determination of which OPPs should be available is done, but this + allows for use of a v1 operating-points table. + +Example: +-------- + +/* From arch/arm/boot/dts/am4372.dtsi */ +cpus { + cpu: cpu@0 { + ... + + operating-points-v2 = <&cpu0_opp_table>; + + ti,syscon-efuse = <&scm_conf 0x610 0x3f 0>; + ti,syscon-rev = <&scm_conf 0x600>; + + ... + }; +}; + +cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2"; + opp50@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <950000>; + opp-supported-hw = <0xFF 0x01>; + opp-suspend; + }; + + opp100@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1100000>; + opp-supported-hw = <0xFF 0x04>; + }; + + opp120@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1200000>; + opp-supported-hw = <0xFF 0x08>; + }; + + oppturbo@800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <1260000>; + opp-supported-hw = <0xFF 0x10>; + }; + + oppnitro@1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1325000>; + opp-supported-hw = <0xFF 0x20>; + }; +}; diff --git b/Documentation/devicetree/bindings/misc/bone_capemgr.txt b/Documentation/devicetree/bindings/misc/bone_capemgr.txt new file mode 100644 index 0000000..7e4fbc9 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/bone_capemgr.txt @@ -0,0 +1,111 @@ +* Beaglebone cape manager driver + +Required properties: +- compatible: "ti,bone-capemgr" +- eeprom: phandle to the EEPROM baseboard. + The EEPROM framework interface is use to obtain the data. + +Required children nodes: + +- baseboardmaps: Contains nodes, which each of the them defines a mapping from + the baseboard EEPROM board-name ID to a DT friendly compatible + string. + + - board-name: The baseboard EEPROM board name, i.e. A335BONE for the + original beaglebone white. + - compatible-name: The DT friendly compatible string to be used for matching + compatible capes, i.e. "ti,beaglebone" + + + - nvmem-cells: Defines the phandles of the nvmem cells of the baseboard and the + slots. + - nvmem-cells: Defines the names of the nvmem cells. Required to have at + least a baseboard cell name. + + - #slots: Defines how many slots are there. + +- Example of a beaglebone cape-manager: + +bone_capemgr { + compatible = "ti,bone-capemgr"; + status = "okay"; + + nvmem-cell = <&baseboard_data + &cape0_data &cape1_data &cape2_data &cape3_data>; + nvmem-cell-names = "baseboard", "slot0", "slot1", "slot2", "slot3"; + + #slots = <4>; + + /* map board revisions to compatible definitions */ + baseboardmaps { + baseboard_beaglebone: board@0 { + board-name = "A335BONE"; + compatible-name = "ti,beaglebone"; + }; + + baseboard_beaglebone_black: board@1 { + board-name = "A335BNLT"; + compatible-name = "ti,beaglebone-black"; + }; + }; +}; + +The format of the cape to be loaded is in a standard overlay format with +the following root properties that are interpreted by the cape manager: + +Required properties: + - compatible: Should be compatible to the baseboard according to the + baseboard map value, i.e. "ti,beaglebone". + - part-numer: Should contain the part-number as stored in the EEPROM. + - version: Should contain a list of all the version that are supported + by the single cape dtbo, i.e. "00A1". + +Optional properties: + - exclusive-use: A string list which state the resources this cape requires. + No processing or matching to anything regarding the internal + kernel state is performed; it's purpose is to guard against + conflicts with other capes. + - priority: A priority to be assigned when loading a cape. A lower value + has higher priority. The purpose of the priority is to control + which cape is loaded first in case of a conflict. + +- Example of a serial cape: + +/dts-v1/; +/plugin/; +/ { + compatible = "ti,beaglebone", "ti,beaglebone-black"; + + /* identification */ + part-number = "BB-BONE-SERL-03"; + version = "00A1"; + + /* state the resources this cape uses */ + exclusive-use = + /* the pin header uses */ + "P9.21", /* uart2_txd */ + "P9.22", /* uart2_rxd */ + /* the hardware ip uses */ + "uart2"; + + fragment@0 { + target = <&am33xx_pinmux>; + __overlay__ { + bb_uart2_pins: pinmux_bb_uart2_pins { + pinctrl-single,pins = < + 0x150 0x21 /* spi0_sclk.uart2_rxd | MODE1 */ + 0x154 0x01 /* spi0_d0.uart2_txd | MODE1 */ + >; + }; + }; + }; + + fragment@1 { + target = <&uart2>; + __overlay__ { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&bb_uart2_pins>; + }; + }; +}; diff --git b/Documentation/devicetree/bindings/pinctrl/ti,iodelay-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,iodelay-pinctrl.txt new file mode 100644 index 0000000..e12f4e5 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,iodelay-pinctrl.txt @@ -0,0 +1,86 @@ +Texas Instruments I/O Delay module configuration pinctrl definition + +Used in conjunction with Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt + +Required Properties: +- compatible: Should be: + "ti,dra7-iodelay" - I/O delay configuration for DRA7 +- reg - must be the register address range of IODelay module +- #address-cells = <1>; +- #size-cells = <0>; + +Important note: Use of "ti,dra7-iodelay" compatible definition need to be +carefully evaluated due to the expectation of glitch during configuration. + +Example: + +dra7_iodelay_core: padconf@4844a000 { + compatible = "ti,dra7-iodelay"; + reg = <0x4844a000 0x0d1c>; + #address-cells = <1>; + #size-cells = <0>; +}; + +Configuration definition follows similar model as the pinctrl-single: +The groups of pin configuration are defined under "pinctrl-single,pins" + +&dra7_iodelay_core { + mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf { + pinctrl-single,pins = < + 0x18c (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A19_IN */ + 0x1a4 (A_DELAY(265) | G_DELAY(360)) /* CFG_GPMC_A20_IN */ + 0x1b0 (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A21_IN */ + 0x1bc (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A22_IN */ + 0x1c8 (A_DELAY(287) | G_DELAY(420)) /* CFG_GPMC_A23_IN */ + 0x1d4 (A_DELAY(144) | G_DELAY(240)) /* CFG_GPMC_A24_IN */ + 0x1e0 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_A25_IN */ + 0x1ec (A_DELAY(120) | G_DELAY(0)) /* CFG_GPMC_A26_IN */ + 0x1f8 (A_DELAY(120) | G_DELAY(180)) /* CFG_GPMC_A27_IN */ + 0x360 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_CS1_IN */ + >; + }; +}; + +Usage in conjunction with pinctrl single: + +For a complete description of the pins both the regular muxing as well as the +iodelay configuration is necessary. For example: + +&dra7_pmx_core { + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + 0x9c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + 0xb0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + 0xa0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + 0xa4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + 0xa8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + 0xac (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + 0x8c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + 0x90 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + 0x94 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + 0x98 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; +}; + +&dra7_iodelay_core { + mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf { + pinctrl-single,pins = < + 0x18c (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A19_IN */ + 0x1a4 (A_DELAY(265) | G_DELAY(360)) /* CFG_GPMC_A20_IN */ + 0x1b0 (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A21_IN */ + 0x1bc (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A22_IN */ + 0x1c8 (A_DELAY(287) | G_DELAY(420)) /* CFG_GPMC_A23_IN */ + 0x1d4 (A_DELAY(144) | G_DELAY(240)) /* CFG_GPMC_A24_IN */ + 0x1e0 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_A25_IN */ + 0x1ec (A_DELAY(120) | G_DELAY(0)) /* CFG_GPMC_A26_IN */ + 0x1f8 (A_DELAY(120) | G_DELAY(180)) /* CFG_GPMC_A27_IN */ + 0x360 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_CS1_IN */ + >; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default &mmc2_iodelay_3v3_conf>; +}; diff --git b/Documentation/devicetree/bindings/usb/generic-onboard-device.txt b/Documentation/devicetree/bindings/usb/generic-onboard-device.txt new file mode 100644 index 0000000..4dd7bca --- /dev/null +++ b/Documentation/devicetree/bindings/usb/generic-onboard-device.txt @@ -0,0 +1,31 @@ +Generic Onboard USB Device + +The node should be located at USB host controller's node or +any USB HUB's node. + +Required properties: +- compatible: should be "generic-onboard-device" + +Optional properties: +- clocks: the input clock for USB device. +- clock-frequency: the frequency for device's clock. +- reset-gpios: Should specify the GPIO for reset. +- reset-duration-us: the duration for assert reset signal, the time unit + is microsecond. + +Example: + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + hub: usb2415@01 { + compatible = "generic-onboard-device"; + reg = <0x01>; + clocks = <&clks IMX6QDL_CLK_CKO>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <10>; + }; +}; diff --git b/Documentation/devicetree/configfs-overlays.txt b/Documentation/devicetree/configfs-overlays.txt new file mode 100644 index 0000000..5fa43e0 --- /dev/null +++ b/Documentation/devicetree/configfs-overlays.txt @@ -0,0 +1,31 @@ +Howto use the configfs overlay interface. + +A device-tree configfs entry is created in /config/device-tree/overlays +and and it is manipulated using standard file system I/O. +Note that this is a debug level interface, for use by developers and +not necessarily something accessed by normal users due to the +security implications of having direct access to the kernel's device tree. + +* To create an overlay you mkdir the directory: + + # mkdir /config/device-tree/overlays/foo + +* Either you echo the overlay firmware file to the path property file. + + # echo foo.dtbo >/config/device-tree/overlays/foo/path + +* Or you cat the contents of the overlay to the dtbo file + + # cat foo.dtbo >/config/device-tree/overlays/foo/dtbo + +The overlay file will be applied, and devices will be created/destroyed +as required. + +To remove it simply rmdir the directory. + + # rmdir /config/device-tree/overlays/foo + +The rationalle of the dual interface (firmware & direct copy) is that each is +better suited to different use patterns. The firmware interface is what's +intended to be used by hardware managers in the kernel, while the copy interface +make sense for developers (since it avoids problems with namespaces). diff --git a/Documentation/devicetree/overlay-notes.txt b/Documentation/devicetree/overlay-notes.txt index d418a6c..3e8df30 100644 --- a/Documentation/devicetree/overlay-notes.txt +++ b/Documentation/devicetree/overlay-notes.txt @@ -100,6 +100,14 @@ Finally, if you need to remove all overlays in one-go, just call of_overlay_destroy_all() which will remove every single one in the correct order. +If your board has multiple slots/places where a single overlay can work +and each slot is defined by a node, you can use the +of_overlay_create_target_index() method to select the target. + +For overlays on probeable busses, use the of_overlay_create_target_root() method +in which you supply a device node as a target root, and which all target +references in the overlay are performed relative to that node. + Overlay DTS Format ------------------ @@ -110,9 +118,11 @@ The DTS of an overlay should have the following format: fragment@0 { /* first child node */ - target=; /* phandle target of the overlay */ + /* phandle target of the overlay */ + target= [, , ...]; or - target-path="/path"; /* target path of the overlay */ + /* target path of the overlay */ + target-path="/path" [ , "/path", ...]; __overlay__ { property-a; /* add property-a to the target */ @@ -131,3 +141,11 @@ Using the non-phandle based target method allows one to use a base DT which does not contain a __symbols__ node, i.e. it was not compiled with the -@ option. The __symbols__ node is only required for the target= method, since it contains the information required to map from a phandle to a tree location. + +Using a target index requires the use of a selector target on the call to +of_overlay_create_target_index(). I.e. passing an index of 0 will select the +target in the foo node, an index of 1 the bar node, etc. + +Note that when using the target root create method all target references must +lie under the target root node. I.e. the overlay is not allowed to 'break' out +of the root. diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 82b42c9..7134c37 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -90,6 +90,7 @@ parameter is applicable: NET Appropriate network support is enabled. NUMA NUMA support is enabled. NFS Appropriate NFS support is enabled. + OF Open Firmware support (device tree) is enabled. OSS OSS sound support is enabled. PV_OPS A paravirtualized kernel is enabled. PARIDE The ParIDE (parallel port IDE) subsystem is enabled. @@ -2759,6 +2760,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. This can be set from sysctl after boot. See Documentation/sysctl/vm.txt for details. + of_overlay_disable [OF] Disable device tree overlays at boot time. + ohci1394_dma=early [HW] enable debugging via the ohci1394 driver. See Documentation/debugging-via-ohci1394.txt for more info. diff --git b/Documentation/misc-devices/bone_capemgr.txt b/Documentation/misc-devices/bone_capemgr.txt new file mode 100644 index 0000000..2a8c766 --- /dev/null +++ b/Documentation/misc-devices/bone_capemgr.txt @@ -0,0 +1,63 @@ +--------------------------- + Beaglebone Cape-Manager +--------------------------- + +The beaglebone cape manager driver allows the automatic use of external +peripheral capes to be automatically supported by Linux without any manual +setup required by the user. + +Each beaglebone cape should contain an EEPROM that describes +it in a fixed I2C address on the i2c2 bus of the baseboard. +The format of the EEPROM is defined in the beaglebone reference +manual at: +http://beagleboard.org/static/beaglebone/latest/Docs/Hardware/BONE_SRM.pdf + +Reading the part number and revision information the manager +requests a firmware file formatted as a device tree overlay blob. + +Applying the overlay the devices are instantiated and the cape is +ready to be used. + +For instance if the part-number is BB-BONE-SERL-03 and the version is 00A1 +the firmware file requested will be BB-BONE-SERL-03-00A1-00A1.dtbo +It will be located by the in-kernel firmware +loader in the usual place, i.e. /lib/firmware/`uname -r`, /lib/firmware etc. + +The driver supports the following parameters (either as part of the kernel +command line or supplied at module insertion time). + +disable_partno: A comma delimited list of PART-NUMBER[:REV] of + disabled capes. +enable_partno: A comma delimited list of PART-NUMBER[:REV[:PRIO]] of + enabled capes. +boot_scan_period: The boot scan period in ms. When the cape manager is built-in + the kernel image, the firmware loader cannot find the files + before the rootfs is mounted. This parameter controls the + period with which the boot state is checked in that case. + +There's a sysfs control interface which is defined at the ABI documentation +area. + +Theory of operation: +-------------------- + +On driver probe the I2C EEPROM of the baseboard is read and information about +the current baseboard is retrieved. This information includes the mapping from +baseboard board name to DT friendly compatible string. I.e. the "A335BONE" board +name from EEPROM is mapped to the "ti,beaglebone" compatible string which should +be present in the dtbo to be loaded. + +Afterwards the EEPROMs declared in each slot are probed, and the EEPROMs found +are decoded keeping track the cape part-number and version data. + +Using the part-number and version a firmware file is requested (the firmware +file requested is -.dtbo). + +The dtbo is unflattend and the resulting device tree is matched against a +compatible baseboard, and in case of multiple parallel loading capes the +priorities defined are honored. That means that when there are multiple capes +being loaded in parallel the ones with the lowest priority number are loaded +first. + +Applying the device tree overlay makes the cape operational, as if it was part +of the kernel's booting device tree. diff --git a/Documentation/printk-formats.txt b/Documentation/printk-formats.txt index 5962949..d1ba882 100644 --- a/Documentation/printk-formats.txt +++ b/Documentation/printk-formats.txt @@ -324,10 +324,49 @@ Network device features: Passed by reference. +Command from struct task_struct + + %pT ls + + For printing executable name excluding path from struct + task_struct. + + Passed by reference. + +Device tree nodes: + + %pO[fnpPcCFr] + + For printing device tree nodes. The optional arguments are: + f device node full_name + n device node name + p device node phandle + P device node path spec (name + @unit) + F device node flags + c major compatible string + C full compatible string + r node reference count + Without any arguments prints full_name (same as %pOf) + The separator when using multiple arguments is '|' + + Examples: + + %pO /foo/bar@0 - Node full name + %pOf /foo/bar@0 - Same as above + %pOfp /foo/bar@0|10 - Node full name + phandle + %pOfcF /foo/bar@0|foo,device|--P- - Node full name + + major compatible string + + node flags + D - dynamic + d - detached + P - Populated + B - Populated bus + + Passed by reference + If you add other %p extensions, please extend lib/test_printf.c with one or more test cases, if at all feasible. - Thank you for your cooperation and attention. diff --git a/MAINTAINERS b/MAINTAINERS index 8c20323..82277f6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2320,6 +2320,14 @@ W: https://linuxtv.org S: Supported F: drivers/media/platform/sti/bdisp +BEAGLEBONE CAPEMANAGER +M: Pantelis Antoniou +S: Maintained +F: drivers/misc/beaglebone-capemgr.c +F: Documentation/misc-devices/bone_capemgr.txt +F: Documentation/devicetree/bindings/misc/bone_capemgr.txt +F: Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr + BEFS FILE SYSTEM S: Orphan F: Documentation/filesystems/befs.txt @@ -11901,6 +11909,13 @@ S: Maintained F: Documentation/usb/ohci.txt F: drivers/usb/host/ohci* +USB Generic Onboard Device Driver +M: Peter Chen +T: git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git +L: linux-usb@vger.kernel.org +S: Maintained +F: drivers/usb/misc/generic_onboard_device.c + USB OTG FSM (Finite State Machine) M: Peter Chen T: git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 274e8a6..ecc9e1a 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -13,7 +13,12 @@ # Ensure linker flags are correct LDFLAGS := -LDFLAGS_vmlinux :=-p --no-undefined -X --pic-veneer +GCCVERSIONISGTE5 := $(shell expr `$(HOSTCC) -dumpversion | cut -f1 -d.` \>= 5) +ifeq "$(GCCVERSIONISGTE5)" "1" +LDFLAGS_vmlinux :=-p --no-undefined -X +else +LDFLAGS_vmlinux :=-p --no-undefined -X --pic-veneer +endif ifeq ($(CONFIG_CPU_ENDIAN_BE8),y) LDFLAGS_vmlinux += --be8 LDFLAGS_MODULE += --be8 diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile index 5be33a2..dbca2e9 100644 --- a/arch/arm/boot/Makefile +++ b/arch/arm/boot/Makefile @@ -27,6 +27,10 @@ export ZRELADDR INITRD_PHYS PARAMS_PHYS targets := Image zImage xipImage bootpImage uImage +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + ifeq ($(CONFIG_XIP_KERNEL),y) $(obj)/xipImage: vmlinux FORCE diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 414b427..efd0034 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,11 +1,17 @@ ifeq ($(CONFIG_OF),y) +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + dtb-$(CONFIG_ARCH_ALPINE) += \ alpine-db.dtb dtb-$(CONFIG_MACH_ARTPEC6) += \ artpec6-devboard.dtb + dtb-$(CONFIG_MACH_ASM9260) += \ alphascale-asm9260-devkit.dtb + # Keep at91 dtb files sorted alphabetically for each SoC dtb-$(CONFIG_SOC_SAM_V4_V5) += \ at91rm9200ek.dtb \ @@ -138,6 +144,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5420-arndale-octa.dtb \ exynos5420-peach-pit.dtb \ exynos5420-smdk5420.dtb \ + exynos5422-artik10-eval.dtb \ exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3-lite.dtb \ exynos5422-odroidxu4.dtb \ @@ -327,6 +334,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-sabreauto.dtb \ imx6dl-sabrelite.dtb \ imx6dl-sabresd.dtb \ + imx6dl-sabresd-wl1835.dtb \ imx6dl-tx6dl-comtft.dtb \ imx6dl-tx6s-8034.dtb \ imx6dl-tx6s-8035.dtb \ @@ -344,6 +352,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-b650v3.dtb \ imx6q-b850v3.dtb \ imx6q-cm-fx6.dtb \ + imx6q-ccimx6sbc.dtb \ imx6q-cubox-i.dtb \ imx6q-dfi-fs700-m60.dtb \ imx6q-dmo-edmqmx6.dtb \ @@ -367,6 +376,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-sabreauto.dtb \ imx6q-sabrelite.dtb \ imx6q-sabresd.dtb \ + imx6q-sabresd-wl1835.dtb \ imx6q-sbc6x.dtb \ imx6q-tbs2910.dtb \ imx6q-tx6q-1010.dtb \ @@ -384,6 +394,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6qp-sabresd.dtb dtb-$(CONFIG_SOC_IMX6SL) += \ imx6sl-evk.dtb \ + imx6sl-evk-wl1835.dtb \ imx6sl-warp.dtb dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-nitrogen6sx.dtb \ @@ -393,6 +404,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-sdb.dtb dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-14x14-evk.dtb \ + imx6ul-14x14-evk-ism43362-b81-evb.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \ @@ -515,6 +527,22 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-base0033.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-sancloud-bbe.dtb \ + am335x-boneblack-bbb-exp-r.dtb \ + am335x-boneblack-bbb-exp-c.dtb \ + am335x-boneblack-bbbmini.dtb \ + am335x-boneblack-wl1835mod.dtb \ + am335x-boneblack-cape-bone-argus.dtb \ + am335x-bone-cape-bone-argus.dtb \ + am335x-arduino-tre.dtb \ + am335x-bonegreen-wireless.dtb \ + am335x-olimex-som.dtb \ + am335x-abbbi.dtb \ + am335x-bonegreen-overlay.dtb \ + am335x-boneblack-overlay.dtb \ + am335x-boneblack-nhdmi-overlay.dtb \ + am335x-boneblack-hdmi-overlay.dtb \ + am335x-boneblack-emmc-overlay.dtb \ am335x-bonegreen.dtb \ am335x-chiliboard.dtb \ am335x-cm-t335.dtb \ @@ -534,6 +562,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-panda.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ + omap4-panda-es-b3.dtb \ omap4-sdp.dtb \ omap4-sdp-es23plus.dtb \ omap4-var-dvk-om44.dtb \ diff --git b/arch/arm/boot/dts/am335x-abbbi.dts b/arch/arm/boot/dts/am335x-abbbi.dts new file mode 100644 index 0000000..accf950 --- /dev/null +++ b/arch/arm/boot/dts/am335x-abbbi.dts @@ -0,0 +1,174 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright 2015 Konsulko Group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am33xx-overlay-edma-fix.dtsi" + +/ { + model = "Arrow BeagleBone Black Industrial"; + compatible = "arrow,am335x-abbbi", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + adi_hdmi_bbbi_pins: adi_hdmi_bbbi_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + adi_hdmi_bbbi_off_pins: adi_hdmi_bbbi_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + 0x1ac (PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahclkx.mcasp0_ahclkx */ + 0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2 */ + 0x194 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + 0x190 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + 0x06c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; + + mcasp0_pins_sleep: mcasp0_pins_sleep { + pinctrl-single,pins = < + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.mcasp0_ahclkx */ + 0x19c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkr.mcasp0_axr2 */ + 0x194 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_fsx.mcasp0_fsx */ + 0x190 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_aclkx.mcasp0_aclkx */ + 0x06c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + adv7511w { + compatible = "adi,adv7511w"; + reg = <0x39>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&adi_hdmi_bbbi_pins>; + pinctrl-1 = <&adi_hdmi_bbbi_off_pins>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; +}; + +&mcasp0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp0_pins>; + pinctrl-1 = <&mcasp0_pins_sleep>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +/ { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; + + hdmi_audio: hdmi_audio@0 { + compatible = "linux,hdmi-audio"; + status = "okay"; + }; + + sound { + compatible = "ti,beaglebone-black-audio"; + ti,model = "TI BeagleBone Black"; + ti,audio-codec = <&hdmi_audio>; + ti,mcasp-controller = <&mcasp0>; + ti,audio-routing = + "HDMI Out", "TX"; + clocks = <&clk_mcasp0>; + clock-names = "mclk"; + }; +}; + +&rtc { + system-power-controller; +}; diff --git b/arch/arm/boot/dts/am335x-arduino-tre.dts b/arch/arm/boot/dts/am335x-arduino-tre.dts new file mode 100644 index 0000000..9e27df0 --- /dev/null +++ b/arch/arm/boot/dts/am335x-arduino-tre.dts @@ -0,0 +1,576 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "TI AM335x Arduino Tre"; + compatible = "ti,am335x-arduino-tre", "ti,am335x-boneblack", "ti,am335x-bone", "ti,am33xx"; + + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 512 MB */ + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&userled_pins>; + + compatible = "gpio-leds"; + + led@0 { + label = "arduino_tre:yel:usr0"; + gpios = <&gpio1 21 0>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led@1 { + label = "arduino_tre:red:usr1"; + gpios = <&gpio1 22 0>; + linux,default-trigger = "none"; + default-state = "off"; + }; + + led@2 { + label = "arduino_tre:blu:usr2"; + gpios = <&gpio1 23 0>; + linux,default-trigger = "none"; + default-state = "off"; + }; + + led@3 { + label = "arduino_tre:grn:usr3"; + gpios = <&gpio1 24 0>; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + }; + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + status = "okay"; + }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "DA830 EVM"; + ti,audio-codec = <&tlv320aic3x>; + ti,mcasp-controller = <&mcasp0>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "LINE2L", "Line In", + "LINE2R", "Line In"; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&userled_pins>; + + userled_pins: pinmux_userled_pins { + pinctrl-single,pins = < + 0x54 0x7 /* gpmc_a5.gpio1_21, OUTPUT | MODE7 */ + 0x58 0x17 /* gpmc_a6.gpio1_22, OUTPUT_PULLUP | MODE7 */ + 0x5c 0x7 /* gpmc_a7.gpio1_23, OUTPUT | MODE7 */ + 0x60 0x17 /* gpmc_a8.gpio1_24, OUTPUT_PULLUP | MODE7 */ + >; + }; + + can_bus_pins: pinmux_can_bus_pins { + pinctrl-single,pins = < + 0x120 0x31 /* DCAN0_RX MODE1 */ + 0x11c 0x01 /* DCAN0_TX MODE1 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + emac_rmii1_pins: pinmux_emac_rmii1_pins { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 0x70 /* i2c0_sda, SLEWCTRL_SLOW | INPUT_PULLUP | MODE0 */ + 0x18c 0x70 /* i2c0_scl, SLEWCTRL_SLOW | INPUT_PULLUP | MODE0 */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x158 0x72 /*spi0_d1-i2c1_sda,SLEWCTRL_SLOW | INPUT_PULLUP | MODE2*/ + 0x15c 0x72 /*spi0_cs0-i2c1_scl,SLEWCTRL_SLOW | INPUT_PULLUP |MODE2*/ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x150 0x72 /*spi0_scl.i2c2_sda,SLEWCTRL_SLOW | INPUT_PULLUP |MODE2*/ + 0x154 0x72 /*spi0_d0.i2c2_scl,SLEWCTRL_SLOW | INPUT_PULLUP | MODE2*/ + >; + }; + + mmc1_pins_default: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x0F0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x0F4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0x0F8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0x0FC (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + 0x1A0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3_18 */ + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; + + mmc1_pins_sleep: pinmux_mmc1_pins_sleep { + pinctrl-single,pins = < + 0x0F0 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x0F4 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x0F8 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x0FC (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x100 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x104 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x1A0 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + tre_ehrpwm1_pins: pinmux_tre_ehrpwm1_pins { + pinctrl-single,pins = < + 0x48 0x06 /* PWM1A ~102 MODE6 */ + 0x4c 0x06 /* PWM1B ~103 MODE6 */ + >; + }; + + tre_ehrpwm2_pins: pinmux_tre_ehrpwm2_pins { + pinctrl-single,pins = < + 0x20 0x04 /* PWM2A ~100 MODE4 */ + 0x24 0x04 /* PWM2B ~101 MODE4 */ + >; + }; + + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + >; + }; + + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + >; + }; + + tre_audio_pins: pinmux_tre_audio_pins { + pinctrl-single,pins = < + 0x1ac 0x00 /*mcasp0_ahclkx (AUD_MCLK)->12MHz, INPUT | MODE0*/ + 0x190 0x20 /* mcasp0_aclkx (AUD_BCLK)->, INPUT | MODE0*/ + 0x194 0x20 /* mcasp0_fsx (AUD_FSX)-> , INPUT | MODE0*/ + 0x198 0x20 /* mcasp0_axr0 (AUD_DIN)<-, INPUT | MODE0*/ + 0x19c 0x22 /* mcasp0_ahclkr-_axr2 (AUD_DOUT)->, | MODE2*/ + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + 0x168 0x14 /* MOSI1 OUTPUT_PULLUP | MODE0 */ + 0x16c 0x34 /* MISO1 INPUT_PULLUP | MODE0 */ + 0x108 0x12 /* SCK1 OUTPUT_PULLUP | MODE0 */ + 0x164 0x12 /* SS1 OUTPUT_PULLUP | MODE0 */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x180 0x30 /* UART1_rxd PULL_UP | MODE0 */ + 0x184 0x00 /* UART1_txd MODE0 */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x12c 0x31 /* UART2_rxd PULL_UP | MODE1 */ + 0x130 0x01 /* UART2_txd MODE1 */ + >; + }; + + uart4_pins: pinmux_uart4_pins { + pinctrl-single,pins = < + 0x70 0x36 /* UART4_rxd PULL_UP | MODE6 */ + 0x74 0x06 /* UART4_txd MODE6 */ + >; + }; +}; + +&dcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&can_bus_pins>; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + tps: tps@24 { + reg = <0x24>; + }; + + rtc@6f { + compatible = "microchip,mcp7941x"; + reg = <0x6f>; + }; + + tlv320aic3x: tlv320aic3x@18 { + compatible = "ti,tlv320aic3x"; + reg = <0x18>; + status = "okay"; + }; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <100000>; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; +}; + +&epwmss1 { + status = "okay"; +}; + +&ehrpwm1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&tre_ehrpwm1_pins>; +}; + +&epwmss2 { + status = "okay"; +}; + +&ehrpwm2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&tre_ehrpwm2_pins>; +}; + +&lcdc { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; + + control@44e10620 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + dr_mode = "peripheral"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@47402000 { + status = "okay"; + }; +}; + +&tps { + compatible = "ti,tps65217"; + ti,pmic-shutdown-controller; + + interrupt-parent = <&intc>; + interrupts = <7>; /* NNMI */ + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1325000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-always-on; + }; + + rtc@44e3e000 { + ti,system-power-controller; + }; + }; +}; + +&mcasp0 { + pinctrl-names = "default"; + pinctrl-0 = <&tre_audio_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + num-serializer = <16>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 2 0 1 0 + 0 0 0 0 + 0 0 0 0 + 0 0 0 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +&mac { + slaves = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emac_rmii1_pins>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rmii"; +}; + +&phy_sel { + rmii-clock-ext; +}; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_sleep>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-inverted; + vmmc-supply = <&vmmcsd_fixed>; +}; + +&rtc { + system-power-controller; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-bone-argus.dtsi b/arch/arm/boot/dts/am335x-bone-argus.dtsi new file mode 100644 index 0000000..21afad3 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-argus.dtsi @@ -0,0 +1,109 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +/ { + ocp { + P8_07_pinmux { + /* gpio2[2] */ + status = "disabled"; + }; + P8_08_pinmux { + /* gpio2[3] */ + status = "disabled"; + }; + P8_09_pinmux { + /* gpio2[5] */ + status = "disabled"; + }; + P8_10_pinmux { + /* gpio2[4] */ + status = "disabled"; + }; + P9_11_pinmux { + /* gpio0[30] */ + status = "disabled"; + }; + P9_17_pinmux { + /* gpio0[5] */ + status = "disabled"; + }; + P9_18_pinmux { + /* gpio0[4] */ + status = "disabled"; + }; + P9_41_pinmux { + /* gpio0[20] */ + status = "disabled"; + }; + P9_42_pinmux { + /* gpio0[7] */ + status = "disabled"; + }; + }; +}; + +/ { + argus-ups { + compatible = "argus-ups"; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&argus_ups_pins>; /* Refer to previous label */ + /* This section communicates the gpio numbers to the driver module */ + /* Note that gpio controllers appear to be numbered from 1-n here rather than 0-(n-1)????? */ + gpios = <&gpio0 30 0>, /* Request */ + <&gpio0 5 0>, /* Acknowledge */ + <&gpio0 4 0>, /* Watchdog */ + <&gpio2 2 0>, /* LED 1 Green */ + <&gpio2 3 0>, /* LED 1 Red */ + <&gpio2 5 0>, /* LED 2 Green */ + <&gpio2 4 0>, /* LED 2 Red */ + <&gpio0 20 0>, /* General Output #1 */ + <&gpio0 7 0>; /* General Output #2 */ + debug = <1>; + shutdown = <1>; + }; +}; + +&am33xx_pinmux { + argus_ups_pins: pinmux_argus_ups_pins { /* Set up pinmux */ + pinctrl-single,pins = < + 0x070 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ + 0x15c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* spi0_cs0.gpio0_5 */ + 0x158 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* spi0_d1.gpio0_4 */ + 0x090 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_advn_ale.gpio_2 */ + 0x094 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */ + 0x09c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */ + 0x098 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_gpmc_wen.gpio2_4 */ + 0x1b4 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* xdma_event_intr1.gpio0_20 */ + 0x164 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* ecap0_in_pwm0_out.gpio0_7 */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + BONE_P9_20 0x73 /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) uart1_ctsn.i2c2_sda */ + BONE_P9_19 0x73 /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) uart1_rtsn.i2c2_scl */ + >; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + status = "okay"; + clock-frequency = <100000>; + + rtc@68 { + compatible = "maxim,ds1307"; + reg = <0x68>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-cape-bone-argus.dts b/arch/arm/boot/dts/am335x-bone-cape-bone-argus.dts new file mode 100644 index 0000000..82218f5 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-cape-bone-argus.dts @@ -0,0 +1,28 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" + +/ { + model = "TI AM335x BeagleBone"; + compatible = "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&ldo3_reg>; +}; + +#include "am335x-bone-argus.dtsi" diff --git b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi new file mode 100644 index 0000000..12464cc --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi @@ -0,0 +1,344 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds_s0>; + + compatible = "gpio-leds"; + + led@2 { + label = "beaglebone:green:usr0"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led@3 { + label = "beaglebone:green:usr1"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led@4 { + label = "beaglebone:green:usr2"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + + led@5 { + label = "beaglebone:green:usr3"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&am33xx_pinmux { + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + AM33XX_IOPAD(0x860, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ + AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x108 (PIN_INPUT | MUX_MODE0) /* mii1_col.mii1_col */ + 0x10c (PIN_INPUT | MUX_MODE0) /* mii1_crs.mii1_crs */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ + >; + }; + + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "peripheral"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; + + baseboard_eeprom: baseboard_eeprom@50 { + compatible = "at,24c256"; + reg = <0x50>; + + #address-cells = <1>; + #size-cells = <1>; + baseboard_data: baseboard_data@0 { + reg = <0 0x100>; + }; + }; +}; + +/include/ "tps65217.dtsi" + +&tps { + /* + * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only + * mode") at poweroff. Most BeagleBone versions do not support RTC-only + * mode and risk hardware damage if this mode is entered. + * + * For details, see linux-omap mailing list May 2015 thread + * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller + * In particular, messages: + * http://www.spinics.net/lists/linux-omap/msg118585.html + * http://www.spinics.net/lists/linux-omap/msg118615.html + * + * You can override this later with + * &tps { /delete-property/ ti,pmic-shutdown-controller; } + * if you want to use RTC-only mode and made sure you are not affected + * by the hardware problems. (Tip: double-check by performing a current + * measurement after shutdown: it should be less than 1 mA.) + */ + ti,pmic-shutdown-controller; + + interrupt-parent = <&intc>; + interrupts = <7>; /* NNMI */ + + regulators { + dcdc1_reg: regulator@0 { + regulator-name = "vdds_dpr"; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1351500>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + regulator-name = "vio,vrtc,vdds"; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + regulator-name = "vdd_3v3aux"; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + regulator-name = "vdd_1v8"; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + regulator-name = "vdd_3v3a"; + regulator-always-on; + }; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "mii"; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + slaves = <1>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; +}; + +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +&rtc { + system-power-controller; +}; diff --git b/arch/arm/boot/dts/am335x-bone-common-universal.dtsi b/arch/arm/boot/dts/am335x-bone-common-universal.dtsi new file mode 100644 index 0000000..781e33f --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-universal.dtsi @@ -0,0 +1,2052 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&am33xx_pinmux { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + /* P8_02 GND */ + /* P8_03 (ZCZ ball R9 ) emmc */ + /* P8_04 (ZCZ ball T9 ) emmc */ + /* P8_05 (ZCZ ball R8 ) emmc */ + /* P8_06 (ZCZ ball T8 ) emmc */ + + /* P8_07 (ZCZ ball R7 ) */ + P8_07_default_pin: pinmux_P8_07_default_pin { + pinctrl-single,pins = <0x090 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_07_gpio_pin: pinmux_P8_07_gpio_pin { + pinctrl-single,pins = <0x090 0x2F>; }; /* Mode 7, RxActive */ + P8_07_gpio_pu_pin: pinmux_P8_07_gpio_pu_pin { + pinctrl-single,pins = <0x090 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_07_gpio_pd_pin: pinmux_P8_07_gpio_pd_pin { + pinctrl-single,pins = <0x090 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_07_timer_pin: pinmux_P8_07_timer_pin { + pinctrl-single,pins = <0x090 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_08 (ZCZ ball T7 ) */ + P8_08_default_pin: pinmux_P8_08_default_pin { + pinctrl-single,pins = <0x094 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_08_gpio_pin: pinmux_P8_08_gpio_pin { + pinctrl-single,pins = <0x094 0x2F>; }; /* Mode 7, RxActive */ + P8_08_gpio_pu_pin: pinmux_P8_08_gpio_pu_pin { + pinctrl-single,pins = <0x094 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_08_gpio_pd_pin: pinmux_P8_08_gpio_pd_pin { + pinctrl-single,pins = <0x094 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_08_timer_pin: pinmux_P8_08_timer_pin { + pinctrl-single,pins = <0x094 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_09 (ZCZ ball T6 ) */ + P8_09_default_pin: pinmux_P8_09_default_pin { + pinctrl-single,pins = <0x09c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_09_gpio_pin: pinmux_P8_09_gpio_pin { + pinctrl-single,pins = <0x09c 0x2F>; }; /* Mode 7, RxActive */ + P8_09_gpio_pu_pin: pinmux_P8_09_gpio_pu_pin { + pinctrl-single,pins = <0x09c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_09_gpio_pd_pin: pinmux_P8_09_gpio_pd_pin { + pinctrl-single,pins = <0x09c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_09_timer_pin: pinmux_P8_09_timer_pin { + pinctrl-single,pins = <0x09c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_10 (ZCZ ball U6 ) */ + P8_10_default_pin: pinmux_P8_10_default_pin { + pinctrl-single,pins = <0x098 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_10_gpio_pin: pinmux_P8_10_gpio_pin { + pinctrl-single,pins = <0x098 0x2F>; }; /* Mode 7, RxActive */ + P8_10_gpio_pu_pin: pinmux_P8_10_gpio_pu_pin { + pinctrl-single,pins = <0x098 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_10_gpio_pd_pin: pinmux_P8_10_gpio_pd_pin { + pinctrl-single,pins = <0x098 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_10_timer_pin: pinmux_P8_10_timer_pin { + pinctrl-single,pins = <0x098 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_11 (ZCZ ball R12) */ + P8_11_default_pin: pinmux_P8_11_default_pin { + pinctrl-single,pins = <0x034 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_11_gpio_pin: pinmux_P8_11_gpio_pin { + pinctrl-single,pins = <0x034 0x2F>; }; /* Mode 7, RxActive */ + P8_11_gpio_pu_pin: pinmux_P8_11_gpio_pu_pin { + pinctrl-single,pins = <0x034 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_11_gpio_pd_pin: pinmux_P8_11_gpio_pd_pin { + pinctrl-single,pins = <0x034 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_11_pruout_pin: pinmux_P8_11_pruout_pin { + pinctrl-single,pins = <0x034 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_11_qep_pin: pinmux_P8_11_qep_pin { + pinctrl-single,pins = <0x034 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_12 (ZCZ ball T12) */ + P8_12_default_pin: pinmux_P8_12_default_pin { + pinctrl-single,pins = <0x030 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_12_gpio_pin: pinmux_P8_12_gpio_pin { + pinctrl-single,pins = <0x030 0x2F>; }; /* Mode 7, RxActive */ + P8_12_gpio_pu_pin: pinmux_P8_12_gpio_pu_pin { + pinctrl-single,pins = <0x030 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_12_gpio_pd_pin: pinmux_P8_12_gpio_pd_pin { + pinctrl-single,pins = <0x030 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_12_pruout_pin: pinmux_P8_12_pruout_pin { + pinctrl-single,pins = <0x030 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_12_qep_pin: pinmux_P8_12_qep_pin { + pinctrl-single,pins = <0x030 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_13 (ZCZ ball T10) */ + P8_13_default_pin: pinmux_P8_13_default_pin { + pinctrl-single,pins = <0x024 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_13_gpio_pin: pinmux_P8_13_gpio_pin { + pinctrl-single,pins = <0x024 0x2F>; }; /* Mode 7, RxActive */ + P8_13_gpio_pu_pin: pinmux_P8_13_gpio_pu_pin { + pinctrl-single,pins = <0x024 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_13_gpio_pd_pin: pinmux_P8_13_gpio_pd_pin { + pinctrl-single,pins = <0x024 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_13_pwm_pin: pinmux_P8_13_pwm_pin { + pinctrl-single,pins = <0x024 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_14 (ZCZ ball T11) */ + P8_14_default_pin: pinmux_P8_14_default_pin { + pinctrl-single,pins = <0x028 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_14_gpio_pin: pinmux_P8_14_gpio_pin { + pinctrl-single,pins = <0x028 0x2F>; }; /* Mode 7, RxActive */ + P8_14_gpio_pu_pin: pinmux_P8_14_gpio_pu_pin { + pinctrl-single,pins = <0x028 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_14_gpio_pd_pin: pinmux_P8_14_gpio_pd_pin { + pinctrl-single,pins = <0x028 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_14_pwm_pin: pinmux_P8_14_pwm_pin { + pinctrl-single,pins = <0x028 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_15 (ZCZ ball U13) */ + P8_15_default_pin: pinmux_P8_15_default_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_gpio_pin: pinmux_P8_15_gpio_pin { + pinctrl-single,pins = <0x03c 0x2F>; }; /* Mode 7, RxActive */ + P8_15_gpio_pu_pin: pinmux_P8_15_gpio_pu_pin { + pinctrl-single,pins = <0x03c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_15_gpio_pd_pin: pinmux_P8_15_gpio_pd_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_pruin_pin: pinmux_P8_15_pruin_pin { + pinctrl-single,pins = <0x03c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_15_qep_pin: pinmux_P8_15_qep_pin { + pinctrl-single,pins = <0x03c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_16 (ZCZ ball V13) */ + P8_16_default_pin: pinmux_P8_16_default_pin { + pinctrl-single,pins = <0x038 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_16_gpio_pin: pinmux_P8_16_gpio_pin { + pinctrl-single,pins = <0x038 0x2F>; }; /* Mode 7, RxActive */ + P8_16_gpio_pu_pin: pinmux_P8_16_gpio_pu_pin { + pinctrl-single,pins = <0x038 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_16_gpio_pd_pin: pinmux_P8_16_gpio_pd_pin { + pinctrl-single,pins = <0x038 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_16_pruin_pin: pinmux_P8_16_pruin_pin { + pinctrl-single,pins = <0x038 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_16_qep_pin: pinmux_P8_16_qep_pin { + pinctrl-single,pins = <0x038 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_17 (ZCZ ball U12) */ + P8_17_default_pin: pinmux_P8_17_default_pin { + pinctrl-single,pins = <0x02c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_17_gpio_pin: pinmux_P8_17_gpio_pin { + pinctrl-single,pins = <0x02c 0x2F>; }; /* Mode 7, RxActive */ + P8_17_gpio_pu_pin: pinmux_P8_17_gpio_pu_pin { + pinctrl-single,pins = <0x02c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_17_gpio_pd_pin: pinmux_P8_17_gpio_pd_pin { + pinctrl-single,pins = <0x02c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_17_pwm_pin: pinmux_P8_17_pwm_pin { + pinctrl-single,pins = <0x02c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_18 (ZCZ ball V12) */ + P8_18_default_pin: pinmux_P8_18_default_pin { + pinctrl-single,pins = <0x08c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_18_gpio_pin: pinmux_P8_18_gpio_pin { + pinctrl-single,pins = <0x08c 0x2F>; }; /* Mode 7, RxActive */ + P8_18_gpio_pu_pin: pinmux_P8_18_gpio_pu_pin { + pinctrl-single,pins = <0x08c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_18_gpio_pd_pin: pinmux_P8_18_gpio_pd_pin { + pinctrl-single,pins = <0x08c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P8_19 (ZCZ ball U10) */ + P8_19_default_pin: pinmux_P8_19_default_pin { + pinctrl-single,pins = <0x020 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_19_gpio_pin: pinmux_P8_19_gpio_pin { + pinctrl-single,pins = <0x020 0x2F>; }; /* Mode 7, RxActive */ + P8_19_gpio_pu_pin: pinmux_P8_19_gpio_pu_pin { + pinctrl-single,pins = <0x020 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_19_gpio_pd_pin: pinmux_P8_19_gpio_pd_pin { + pinctrl-single,pins = <0x020 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_19_pwm_pin: pinmux_P8_19_pwm_pin { + pinctrl-single,pins = <0x020 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_20 (ZCZ ball V9 ) emmc */ + /* P8_21 (ZCZ ball U9 ) emmc */ + /* P8_22 (ZCZ ball V8 ) emmc */ + /* P8_23 (ZCZ ball U8 ) emmc */ + /* P8_24 (ZCZ ball V7 ) emmc */ + /* P8_25 (ZCZ ball U7 ) emmc */ + + /* P8_26 (ZCZ ball V6 ) */ + P8_26_default_pin: pinmux_P8_26_default_pin { + pinctrl-single,pins = <0x07c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_26_gpio_pin: pinmux_P8_26_gpio_pin { + pinctrl-single,pins = <0x07c 0x2F>; }; /* Mode 7, RxActive */ + P8_26_gpio_pu_pin: pinmux_P8_26_gpio_pu_pin { + pinctrl-single,pins = <0x07c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_26_gpio_pd_pin: pinmux_P8_26_gpio_pd_pin { + pinctrl-single,pins = <0x07c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P8_27 (ZCZ ball U5 ) hdmi */ + P8_27_default_pin: pinmux_P8_27_default_pin { + pinctrl-single,pins = <0x0e0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_27_gpio_pin: pinmux_P8_27_gpio_pin { + pinctrl-single,pins = <0x0e0 0x2F>; }; /* Mode 7, RxActive */ + P8_27_gpio_pu_pin: pinmux_P8_27_gpio_pu_pin { + pinctrl-single,pins = <0x0e0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_27_gpio_pd_pin: pinmux_P8_27_gpio_pd_pin { + pinctrl-single,pins = <0x0e0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_27_pruout_pin: pinmux_P8_27_pruout_pin { + pinctrl-single,pins = <0x0e0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_27_pruin_pin: pinmux_P8_27_pruin_pin { + pinctrl-single,pins = <0x0e0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_27_hdmi_pin: pinmux_P8_27_hdmi_pin { + pinctrl-single,pins = <0x0e0 0x00>; }; /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_28 (ZCZ ball V5 ) hdmi */ + P8_28_default_pin: pinmux_P8_28_default_pin { + pinctrl-single,pins = <0x0e8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_28_gpio_pin: pinmux_P8_28_gpio_pin { + pinctrl-single,pins = <0x0e8 0x2F>; }; /* Mode 7, RxActive */ + P8_28_gpio_pu_pin: pinmux_P8_28_gpio_pu_pin { + pinctrl-single,pins = <0x0e8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_28_gpio_pd_pin: pinmux_P8_28_gpio_pd_pin { + pinctrl-single,pins = <0x0e8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_28_pruout_pin: pinmux_P8_28_pruout_pin { + pinctrl-single,pins = <0x0e8 0x05>; }; /* Mode 5, Pull-Down */ + P8_28_pruin_pin: pinmux_P8_28_pruin_pin { + pinctrl-single,pins = <0x0e8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_28_hdmi_pin: pinmux_P8_28_hdmi_pin { + pinctrl-single,pins = <0x0e8 0x00>; }; /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_29 (ZCZ ball R5 ) hdmi */ + P8_29_default_pin: pinmux_P8_29_default_pin { + pinctrl-single,pins = <0x0e4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_29_gpio_pin: pinmux_P8_29_gpio_pin { + pinctrl-single,pins = <0x0e4 0x2F>; }; /* Mode 7, RxActive */ + P8_29_gpio_pu_pin: pinmux_P8_29_gpio_pu_pin { + pinctrl-single,pins = <0x0e4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_29_gpio_pd_pin: pinmux_P8_29_gpio_pd_pin { + pinctrl-single,pins = <0x0e4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_29_pruout_pin: pinmux_P8_29_pruout_pin { + pinctrl-single,pins = <0x0e4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_29_pruin_pin: pinmux_P8_29_pruin_pin { + pinctrl-single,pins = <0x0e4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_29_hdmi_pin: pinmux_P8_29_hdmi_pin { + pinctrl-single,pins = <0x0e4 0x00>; }; /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_30 (ZCZ ball R6 ) hdmi */ + P8_30_default_pin: pinmux_P8_30_default_pin { + pinctrl-single,pins = <0x0ec 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_30_gpio_pin: pinmux_P8_30_gpio_pin { + pinctrl-single,pins = <0x0ec 0x2F>; }; /* Mode 7, RxActive */ + P8_30_gpio_pu_pin: pinmux_P8_30_gpio_pu_pin { + pinctrl-single,pins = <0x0ec 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_30_gpio_pd_pin: pinmux_P8_30_gpio_pd_pin { + pinctrl-single,pins = <0x0ec 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_30_pruout_pin: pinmux_P8_30_pruout_pin { + pinctrl-single,pins = <0x0ec 0x05>; }; /* Mode 5, Pull-Down*/ + P8_30_pruin_pin: pinmux_P8_30_pruin_pin { + pinctrl-single,pins = <0x0ec 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_30_hdmi_pin: pinmux_P8_30_hdmi_pin { + pinctrl-single,pins = <0x0ec 0x00>; }; /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_31 (ZCZ ball V4 ) hdmi */ + P8_31_default_pin: pinmux_P8_31_default_pin { + pinctrl-single,pins = <0x0d8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_31_gpio_pin: pinmux_P8_31_gpio_pin { + pinctrl-single,pins = <0x0d8 0x2F>; }; /* Mode 7, RxActive */ + P8_31_gpio_pu_pin: pinmux_P8_31_gpio_pu_pin { + pinctrl-single,pins = <0x0d8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_31_gpio_pd_pin: pinmux_P8_31_gpio_pd_pin { + pinctrl-single,pins = <0x0d8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_31_uart_pin: pinmux_P8_31_uart_pin { + pinctrl-single,pins = <0x0d8 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_31_hdmi_pin: pinmux_P8_31_hdmi_pin { + pinctrl-single,pins = <0x0d8 0x08>; }; /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_32 (ZCZ ball T5 ) hdmi */ + P8_32_default_pin: pinmux_P8_32_default_pin { + pinctrl-single,pins = <0x0dc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_32_gpio_pin: pinmux_P8_32_gpio_pin { + pinctrl-single,pins = <0x0dc 0x2F>; }; /* Mode 7, RxActive */ + P8_32_gpio_pu_pin: pinmux_P8_32_gpio_pu_pin { + pinctrl-single,pins = <0x0dc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_32_gpio_pd_pin: pinmux_P8_32_gpio_pd_pin { + pinctrl-single,pins = <0x0dc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_32_uart_pin: pinmux_P8_32_uart_pin { + pinctrl-single,pins = <0x0dc 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_32_hdmi_pin: pinmux_P8_32_hdmi_pin { + pinctrl-single,pins = <0x0dc 0x08>; }; /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_33 (ZCZ ball V3 ) hdmi */ + P8_33_default_pin: pinmux_P8_33_default_pin { + pinctrl-single,pins = <0x0d4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_33_gpio_pin: pinmux_P8_33_gpio_pin { + pinctrl-single,pins = <0x0d4 0x2F>; }; /* Mode 7, RxActive */ + P8_33_gpio_pu_pin: pinmux_P8_33_gpio_pu_pin { + pinctrl-single,pins = <0x0d4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_33_gpio_pd_pin: pinmux_P8_33_gpio_pd_pin { + pinctrl-single,pins = <0x0d4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_33_hdmi_pin: pinmux_P8_33_hdmi_pin { + pinctrl-single,pins = <0x0d4 0x08>; }; /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_34 (ZCZ ball U4 ) hdmi */ + P8_34_default_pin: pinmux_P8_34_default_pin { + pinctrl-single,pins = <0x0cc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_34_gpio_pin: pinmux_P8_34_gpio_pin { + pinctrl-single,pins = <0x0cc 0x2F>; }; /* Mode 7, RxActive */ + P8_34_gpio_pu_pin: pinmux_P8_34_gpio_pu_pin { + pinctrl-single,pins = <0x0cc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_34_gpio_pd_pin: pinmux_P8_34_gpio_pd_pin { + pinctrl-single,pins = <0x0cc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_34_pwm_pin: pinmux_P8_34_pwm_pin { + pinctrl-single,pins = <0x0cc 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_34_hdmi_pin: pinmux_P8_34_hdmi_pin { + pinctrl-single,pins = <0x0cc 0x08>; }; /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_35 (ZCZ ball V2 ) hdmi */ + P8_35_default_pin: pinmux_P8_35_default_pin { + pinctrl-single,pins = <0x0d0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_35_gpio_pin: pinmux_P8_35_gpio_pin { + pinctrl-single,pins = <0x0d0 0x2F>; }; /* Mode 7, RxActive */ + P8_35_gpio_pu_pin: pinmux_P8_35_gpio_pu_pin { + pinctrl-single,pins = <0x0d0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_35_gpio_pd_pin: pinmux_P8_35_gpio_pd_pin { + pinctrl-single,pins = <0x0d0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_35_hdmi_pin: pinmux_P8_35_hdmi_pin { + pinctrl-single,pins = <0x0d0 0x08>; }; /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_36 (ZCZ ball U3 ) hdmi */ + P8_36_default_pin: pinmux_P8_36_default_pin { + pinctrl-single,pins = <0x0c8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_36_gpio_pin: pinmux_P8_36_gpio_pin { + pinctrl-single,pins = <0x0c8 0x2F>; }; /* Mode 7, RxActive */ + P8_36_gpio_pu_pin: pinmux_P8_36_gpio_pu_pin { + pinctrl-single,pins = <0x0c8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_36_gpio_pd_pin: pinmux_P8_36_gpio_pd_pin { + pinctrl-single,pins = <0x0c8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_36_pwm_pin: pinmux_P8_36_pwm_pin { + pinctrl-single,pins = <0x0c8 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_36_hdmi_pin: pinmux_P8_36_hdmi_pin { + pinctrl-single,pins = <0x0c8 0x08>; }; /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_37 (ZCZ ball U1 ) hdmi */ + P8_37_default_pin: pinmux_P8_37_default_pin { + pinctrl-single,pins = <0x0c0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_37_gpio_pin: pinmux_P8_37_gpio_pin { + pinctrl-single,pins = <0x0c0 0x2F>; }; /* Mode 7, RxActive */ + P8_37_gpio_pu_pin: pinmux_P8_37_gpio_pu_pin { + pinctrl-single,pins = <0x0c0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_37_gpio_pd_pin: pinmux_P8_37_gpio_pd_pin { + pinctrl-single,pins = <0x0c0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_37_uart_pin: pinmux_P8_37_uart_pin { + pinctrl-single,pins = <0x0c0 0x04>; }; /* Mode 4, Pull-Down*/ + P8_37_pwm_pin: pinmux_P8_37_pwm_pin { + pinctrl-single,pins = <0x0c0 0x02>; }; /* Mode 2, Pull-Down*/ + P8_37_hdmi_pin: pinmux_P8_37_hdmi_pin { + pinctrl-single,pins = <0x0c0 0x08>; }; /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + + /* P8_38 (ZCZ ball U2 ) hdmi */ + P8_38_default_pin: pinmux_P8_38_default_pin { + pinctrl-single,pins = <0x0c4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_38_gpio_pin: pinmux_P8_38_gpio_pin { + pinctrl-single,pins = <0x0c4 0x2F>; }; /* Mode 7, RxActive */ + P8_38_gpio_pu_pin: pinmux_P8_38_gpio_pu_pin { + pinctrl-single,pins = <0x0c4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_38_gpio_pd_pin: pinmux_P8_38_gpio_pd_pin { + pinctrl-single,pins = <0x0c4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_38_uart_pin: pinmux_P8_38_uart_pin { + pinctrl-single,pins = <0x0c4 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_38_pwm_pin: pinmux_P8_38_pwm_pin { + pinctrl-single,pins = <0x0c4 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_38_hdmi_pin: pinmux_P8_38_hdmi_pin { + pinctrl-single,pins = <0x0c4 0x08>; }; /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + + /* P8_39 (ZCZ ball T3 ) hdmi */ + P8_39_default_pin: pinmux_P8_39_default_pin { + pinctrl-single,pins = <0x0b8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_39_gpio_pin: pinmux_P8_39_gpio_pin { + pinctrl-single,pins = <0x0b8 0x2F>; }; /* Mode 7, RxActive */ + P8_39_gpio_pu_pin: pinmux_P8_39_gpio_pu_pin { + pinctrl-single,pins = <0x0b8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_39_gpio_pd_pin: pinmux_P8_39_gpio_pd_pin { + pinctrl-single,pins = <0x0b8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_39_pruout_pin: pinmux_P8_39_pruout_pin { + pinctrl-single,pins = <0x0b8 0x05>; }; /* Mode 5, Pull-Down*/ + P8_39_pruin_pin: pinmux_P8_39_pruin_pin { + pinctrl-single,pins = <0x0b8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_39_hdmi_pin: pinmux_P8_39_hdmi_pin { + pinctrl-single,pins = <0x0b8 0x08>; }; /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_40 (ZCZ ball T4 ) hdmi */ + P8_40_default_pin: pinmux_P8_40_default_pin { + pinctrl-single,pins = <0x0bc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_40_gpio_pin: pinmux_P8_40_gpio_pin { + pinctrl-single,pins = <0x0bc 0x2F>; }; /* Mode 7, RxActive */ + P8_40_gpio_pu_pin: pinmux_P8_40_gpio_pu_pin { + pinctrl-single,pins = <0x0bc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_40_gpio_pd_pin: pinmux_P8_40_gpio_pd_pin { + pinctrl-single,pins = <0x0bc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_40_pruout_pin: pinmux_P8_40_pruout_pin { + pinctrl-single,pins = <0x0bc 0x05>; }; /* Mode 5, Pull-Down*/ + P8_40_pruin_pin: pinmux_P8_40_pruin_pin { + pinctrl-single,pins = <0x0bc 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_40_hdmi_pin: pinmux_P8_40_hdmi_pin { + pinctrl-single,pins = <0x0bc 0x08>; }; /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_41 (ZCZ ball T1 ) hdmi */ + P8_41_default_pin: pinmux_P8_41_default_pin { + pinctrl-single,pins = <0x0b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_41_gpio_pin: pinmux_P8_41_gpio_pin { + pinctrl-single,pins = <0x0b0 0x2F>; }; /* Mode 7, RxActive */ + P8_41_gpio_pu_pin: pinmux_P8_41_gpio_pu_pin { + pinctrl-single,pins = <0x0b0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_41_gpio_pd_pin: pinmux_P8_41_gpio_pd_pin { + pinctrl-single,pins = <0x0b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_41_pruout_pin: pinmux_P8_41_pruout_pin { + pinctrl-single,pins = <0x0b0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_41_pruin_pin: pinmux_P8_41_pruin_pin { + pinctrl-single,pins = <0x0b0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_41_hdmi_pin: pinmux_P8_41_hdmi_pin { + pinctrl-single,pins = <0x0b0 0x08>; }; /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_42 (ZCZ ball T2 ) hdmi */ + P8_42_default_pin: pinmux_P8_42_default_pin { + pinctrl-single,pins = <0x0b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_42_gpio_pin: pinmux_P8_42_gpio_pin { + pinctrl-single,pins = <0x0b4 0x2F>; }; /* Mode 7, RxActive */ + P8_42_gpio_pu_pin: pinmux_P8_42_gpio_pu_pin { + pinctrl-single,pins = <0x0b4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_42_gpio_pd_pin: pinmux_P8_42_gpio_pd_pin { + pinctrl-single,pins = <0x0b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_42_pruout_pin: pinmux_P8_42_pruout_pin { + pinctrl-single,pins = <0x0b4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_42_pruin_pin: pinmux_P8_42_pruin_pin { + pinctrl-single,pins = <0x0b4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_42_hdmi_pin: pinmux_P8_42_hdmi_pin { + pinctrl-single,pins = <0x0b4 0x08>; }; /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_43 (ZCZ ball R3 ) hdmi */ + P8_43_default_pin: pinmux_P8_43_default_pin { + pinctrl-single,pins = <0x0a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_43_gpio_pin: pinmux_P8_43_gpio_pin { + pinctrl-single,pins = <0x0a8 0x2F>; }; /* Mode 7, RxActive */ + P8_43_gpio_pu_pin: pinmux_P8_43_gpio_pu_pin { + pinctrl-single,pins = <0x0a8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_43_gpio_pd_pin: pinmux_P8_43_gpio_pd_pin { + pinctrl-single,pins = <0x0a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_43_pruout_pin: pinmux_P8_43_pruout_pin { + pinctrl-single,pins = <0x0a8 0x05>; }; /* Mode 5, Pull-Down*/ + P8_43_pruin_pin: pinmux_P8_43_pruin_pin { + pinctrl-single,pins = <0x0a8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_43_pwm_pin: pinmux_P8_43_pwm_pin { + pinctrl-single,pins = <0x0a8 0x03>; }; /* Mode 3, Pull-Down */ + P8_43_hdmi_pin: pinmux_P8_43_hdmi_pin { + pinctrl-single,pins = <0x0a8 0x08>; }; /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_44 (ZCZ ball R4 ) hdmi */ + P8_44_default_pin: pinmux_P8_44_default_pin { + pinctrl-single,pins = <0x0ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_44_gpio_pin: pinmux_P8_44_gpio_pin { + pinctrl-single,pins = <0x0ac 0x2F>; }; /* Mode 7, RxActive */ + P8_44_gpio_pu_pin: pinmux_P8_44_gpio_pu_pin { + pinctrl-single,pins = <0x0ac 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_44_gpio_pd_pin: pinmux_P8_44_gpio_pd_pin { + pinctrl-single,pins = <0x0ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_44_pruout_pin: pinmux_P8_44_pruout_pin { + pinctrl-single,pins = <0x0ac 0x05>; }; /* Mode 5, Pull-Down*/ + P8_44_pruin_pin: pinmux_P8_44_pruin_pin { + pinctrl-single,pins = <0x0ac 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_44_pwm_pin: pinmux_P8_44_pwm_pin { + pinctrl-single,pins = <0x0ac 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P8_44_hdmi_pin: pinmux_P8_44_hdmi_pin { + pinctrl-single,pins = <0x0ac 0x08>; }; /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_45 (ZCZ ball R1 ) hdmi */ + P8_45_default_pin: pinmux_P8_45_default_pin { + pinctrl-single,pins = <0x0a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_45_gpio_pin: pinmux_P8_45_gpio_pin { + pinctrl-single,pins = <0x0a0 0x2F>; }; /* Mode 7, RxActive */ + P8_45_gpio_pu_pin: pinmux_P8_45_gpio_pu_pin { + pinctrl-single,pins = <0x0a0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_45_gpio_pd_pin: pinmux_P8_45_gpio_pd_pin { + pinctrl-single,pins = <0x0a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_45_pruout_pin: pinmux_P8_45_pruout_pin { + pinctrl-single,pins = <0x0a0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_45_pruin_pin: pinmux_P8_45_pruin_pin { + pinctrl-single,pins = <0x0a0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_45_pwm_pin: pinmux_P8_45_pwm_pin { + pinctrl-single,pins = <0x0a0 0x03>; }; /* Mode 3, Pull-Down*/ + P8_45_hdmi_pin: pinmux_P8_45_hdmi_pin { + pinctrl-single,pins = <0x0a0 0x08>; }; /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_46 (ZCZ ball R2 ) hdmi */ + P8_46_default_pin: pinmux_P8_46_default_pin { + pinctrl-single,pins = <0x0a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_46_gpio_pin: pinmux_P8_46_gpio_pin { + pinctrl-single,pins = <0x0a4 0x2F>; }; /* Mode 7, RxActive */ + P8_46_gpio_pu_pin: pinmux_P8_46_gpio_pu_pin { + pinctrl-single,pins = <0x0a4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_46_gpio_pd_pin: pinmux_P8_46_gpio_pd_pin { + pinctrl-single,pins = <0x0a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_46_pruout_pin: pinmux_P8_46_pruout_pin { + pinctrl-single,pins = <0x0a4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_46_pruin_pin: pinmux_P8_46_pruin_pin { + pinctrl-single,pins = <0x0a4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_46_pwm_pin: pinmux_P8_46_pwm_pin { + pinctrl-single,pins = <0x0a4 0x03>; }; /* Mode 3, Pull-Down*/ + P8_46_hdmi_pin: pinmux_P8_46_hdmi_pin { + pinctrl-single,pins = <0x0a4 0x08>; }; /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + /* P9_02 GND */ + /* P9_03 3.3V */ + /* P9_04 3.3V */ + /* P9_05 VDD_5V */ + /* P9_06 VDD_5V */ + /* P9_07 SYS_5V */ + /* P9_08 SYS_5V */ + /* P9_09 PWR_BUT */ + /* P9_10 (ZCZ ball A10) RESETn */ + + /* P9_11 (ZCZ ball T17) */ + P9_11_default_pin: pinmux_P9_11_default_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pin: pinmux_P9_11_gpio_pin { + pinctrl-single,pins = <0x070 0x2F>; }; /* Mode 7, RxActive */ + P9_11_gpio_pu_pin: pinmux_P9_11_gpio_pu_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pd_pin: pinmux_P9_11_gpio_pd_pin { + pinctrl-single,pins = <0x070 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_11_uart_pin: pinmux_P9_11_uart_pin { + pinctrl-single,pins = <0x070 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_12 (ZCZ ball U18) */ + P9_12_default_pin: pinmux_P9_12_default_pin { + pinctrl-single,pins = <0x078 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_12_gpio_pin: pinmux_P9_12_gpio_pin { + pinctrl-single,pins = <0x078 0x2F>; }; /* Mode 7, RxActive */ + P9_12_gpio_pu_pin: pinmux_P9_12_gpio_pu_pin { + pinctrl-single,pins = <0x078 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_12_gpio_pd_pin: pinmux_P9_12_gpio_pd_pin { + pinctrl-single,pins = <0x078 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P9_13 (ZCZ ball U17) */ + P9_13_default_pin: pinmux_P9_13_default_pin { + pinctrl-single,pins = <0x074 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_13_gpio_pin: pinmux_P9_13_gpio_pin { + pinctrl-single,pins = <0x074 0x2F>; }; /* Mode 7, RxActive */ + P9_13_gpio_pu_pin: pinmux_P9_13_gpio_pu_pin { + pinctrl-single,pins = <0x074 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_13_gpio_pd_pin: pinmux_P9_13_gpio_pd_pin { + pinctrl-single,pins = <0x074 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_13_uart_pin: pinmux_P9_13_uart_pin { + pinctrl-single,pins = <0x074 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_14 (ZCZ ball U14) */ + P9_14_default_pin: pinmux_P9_14_default_pin { + pinctrl-single,pins = <0x048 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_14_gpio_pin: pinmux_P9_14_gpio_pin { + pinctrl-single,pins = <0x048 0x2F>; }; /* Mode 7, RxActive */ + P9_14_gpio_pu_pin: pinmux_P9_14_gpio_pu_pin { + pinctrl-single,pins = <0x048 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_14_gpio_pd_pin: pinmux_P9_14_gpio_pd_pin { + pinctrl-single,pins = <0x048 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_14_pwm_pin: pinmux_P9_14_pwm_pin { + pinctrl-single,pins = <0x048 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_15 (ZCZ ball R13) */ + P9_15_default_pin: pinmux_P9_15_default_pin { + pinctrl-single,pins = <0x040 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_15_gpio_pin: pinmux_P9_15_gpio_pin { + pinctrl-single,pins = <0x040 0x2F>; }; /* Mode 7, RxActive */ + P9_15_gpio_pu_pin: pinmux_P9_15_gpio_pu_pin { + pinctrl-single,pins = <0x040 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_15_gpio_pd_pin: pinmux_P9_15_gpio_pd_pin { + pinctrl-single,pins = <0x040 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_15_pwm_pin: pinmux_P9_15_pwm_pin { + pinctrl-single,pins = <0x040 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_16 (ZCZ ball T14) */ + P9_16_default_pin: pinmux_P9_16_default_pin { + pinctrl-single,pins = <0x04c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_16_gpio_pin: pinmux_P9_16_gpio_pin { + pinctrl-single,pins = <0x04c 0x2F>; }; /* Mode 7, RxActive */ + P9_16_gpio_pu_pin: pinmux_P9_16_gpio_pu_pin { + pinctrl-single,pins = <0x04c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_16_gpio_pd_pin: pinmux_P9_16_gpio_pd_pin { + pinctrl-single,pins = <0x04c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_16_pwm_pin: pinmux_P9_16_pwm_pin { + pinctrl-single,pins = <0x04c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_17 (ZCZ ball A16) */ + P9_17_default_pin: pinmux_P9_17_default_pin { + pinctrl-single,pins = <0x15c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_17_gpio_pin: pinmux_P9_17_gpio_pin { + pinctrl-single,pins = <0x15c 0x2F>; }; /* Mode 7, RxActive */ + P9_17_gpio_pu_pin: pinmux_P9_17_gpio_pu_pin { + pinctrl-single,pins = <0x15c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_17_gpio_pd_pin: pinmux_P9_17_gpio_pd_pin { + pinctrl-single,pins = <0x15c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_17_spi_pin: pinmux_P9_17_spi_pin { + pinctrl-single,pins = <0x15c 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_17_i2c_pin: pinmux_P9_17_i2c_pin { + pinctrl-single,pins = <0x15c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_17_pwm_pin: pinmux_P9_17_pwm_pin { + pinctrl-single,pins = <0x15c 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_18 (ZCZ ball B16) */ + P9_18_default_pin: pinmux_P9_18_default_pin { + pinctrl-single,pins = <0x158 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_18_gpio_pin: pinmux_P9_18_gpio_pin { + pinctrl-single,pins = <0x158 0x2F>; }; /* Mode 7, RxActive */ + P9_18_gpio_pu_pin: pinmux_P9_18_gpio_pu_pin { + pinctrl-single,pins = <0x158 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_18_gpio_pd_pin: pinmux_P9_18_gpio_pd_pin { + pinctrl-single,pins = <0x158 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_18_spi_pin: pinmux_P9_18_spi_pin { + pinctrl-single,pins = <0x158 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_18_i2c_pin: pinmux_P9_18_i2c_pin { + pinctrl-single,pins = <0x158 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_18_pwm_pin: pinmux_P9_18_pwm_pin { + pinctrl-single,pins = <0x158 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_19 (ZCZ ball D17) */ + P9_19_default_pin: pinmux_P9_19_default_pin { + pinctrl-single,pins = <0x17c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_19_gpio_pin: pinmux_P9_19_gpio_pin { + pinctrl-single,pins = <0x17c 0x2F>; }; /* Mode 7, RxActive */ + P9_19_gpio_pu_pin: pinmux_P9_19_gpio_pu_pin { + pinctrl-single,pins = <0x17c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_19_gpio_pd_pin: pinmux_P9_19_gpio_pd_pin { + pinctrl-single,pins = <0x17c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_19_can_pin: pinmux_P9_19_can_pin { + pinctrl-single,pins = <0x17c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_19_i2c_pin: pinmux_P9_19_i2c_pin { + pinctrl-single,pins = <0x17c 0x73>; }; /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) */ + + /* P9_20 (ZCZ ball D18) */ + P9_20_default_pin: pinmux_P9_20_default_pin { + pinctrl-single,pins = <0x178 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_20_gpio_pin: pinmux_P9_20_gpio_pin { + pinctrl-single,pins = <0x178 0x2F>; }; /* Mode 7, RxActive */ + P9_20_gpio_pu_pin: pinmux_P9_20_gpio_pu_pin { + pinctrl-single,pins = <0x178 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_20_gpio_pd_pin: pinmux_P9_20_gpio_pd_pin { + pinctrl-single,pins = <0x178 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_20_can_pin: pinmux_P9_20_can_pin { + pinctrl-single,pins = <0x178 0x12>; }; /* Mode 2, Pull-Up, RxActive */ + P9_20_i2c_pin: pinmux_P9_20_i2c_pin { + pinctrl-single,pins = <0x178 0x73>; }; /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) */ + + /* P9_21 (ZCZ ball B17) */ + P9_21_default_pin: pinmux_P9_21_default_pin { + pinctrl-single,pins = <0x154 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_21_gpio_pin: pinmux_P9_21_gpio_pin { + pinctrl-single,pins = <0x154 0x2F>; }; /* Mode 7, RxActive */ + P9_21_gpio_pu_pin: pinmux_P9_21_gpio_pu_pin { + pinctrl-single,pins = <0x154 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_21_gpio_pd_pin: pinmux_P9_21_gpio_pd_pin { + pinctrl-single,pins = <0x154 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_21_spi_pin: pinmux_P9_21_spi_pin { + pinctrl-single,pins = <0x154 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_21_uart_pin: pinmux_P9_21_uart_pin { + pinctrl-single,pins = <0x154 0x31>; }; /* Mode 1, Pull-Up, RxActive */ + P9_21_i2c_pin: pinmux_P9_21_i2c_pin { + pinctrl-single,pins = <0x154 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_21_pwm_pin: pinmux_P9_21_pwm_pin { + pinctrl-single,pins = <0x154 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_22 (ZCZ ball A17) */ + P9_22_default_pin: pinmux_P9_22_default_pin { + pinctrl-single,pins = <0x150 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_22_gpio_pin: pinmux_P9_22_gpio_pin { + pinctrl-single,pins = <0x150 0x2F>; }; /* Mode 7, RxActive */ + P9_22_gpio_pu_pin: pinmux_P9_22_gpio_pu_pin { + pinctrl-single,pins = <0x150 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_22_gpio_pd_pin: pinmux_P9_22_gpio_pd_pin { + pinctrl-single,pins = <0x150 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_22_spi_pin: pinmux_P9_22_spi_pin { + pinctrl-single,pins = <0x150 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_22_uart_pin: pinmux_P9_22_uart_pin { + pinctrl-single,pins = <0x150 0x31>; }; /* Mode 1, Pull-Up, RxActive */ + P9_22_i2c_pin: pinmux_P9_22_i2c_pin { + pinctrl-single,pins = <0x150 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_22_pwm_pin: pinmux_P9_22_pwm_pin { + pinctrl-single,pins = <0x150 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_23 (ZCZ ball V14) */ + P9_23_default_pin: pinmux_P9_23_default_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_gpio_pin: pinmux_P9_23_gpio_pin { + pinctrl-single,pins = <0x044 0x2F>; }; /* Mode 7, RxActive */ + P9_23_gpio_pu_pin: pinmux_P9_23_gpio_pu_pin { + pinctrl-single,pins = <0x044 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_23_gpio_pd_pin: pinmux_P9_23_gpio_pd_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_pwm_pin: pinmux_P9_23_pwm_pin { + pinctrl-single,pins = <0x044 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_24 (ZCZ ball D15) */ + P9_24_default_pin: pinmux_P9_24_default_pin { + pinctrl-single,pins = <0x184 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_24_gpio_pin: pinmux_P9_24_gpio_pin { + pinctrl-single,pins = <0x184 0x2F>; }; /* Mode 7, RxActive */ + P9_24_gpio_pu_pin: pinmux_P9_24_gpio_pu_pin { + pinctrl-single,pins = <0x184 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_24_gpio_pd_pin: pinmux_P9_24_gpio_pd_pin { + pinctrl-single,pins = <0x184 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_24_uart_pin: pinmux_P9_24_uart_pin { + pinctrl-single,pins = <0x184 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_24_can_pin: pinmux_P9_24_can_pin { + pinctrl-single,pins = <0x184 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_24_i2c_pin: pinmux_P9_24_i2c_pin { + pinctrl-single,pins = <0x184 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + P9_24_pruin_pin: pinmux_P9_24_pruin_pin { + pinctrl-single,pins = <0x184 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_25 (ZCZ ball A14) Audio */ + P9_25_default_pin: pinmux_P9_25_default_pin { + pinctrl-single,pins = <0x1ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_25_gpio_pin: pinmux_P9_25_gpio_pin { + pinctrl-single,pins = <0x1ac 0x2F>; }; /* Mode 7, RxActive */ + P9_25_gpio_pu_pin: pinmux_P9_25_gpio_pu_pin { + pinctrl-single,pins = <0x1ac 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_25_gpio_pd_pin: pinmux_P9_25_gpio_pd_pin { + pinctrl-single,pins = <0x1ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_25_qep_pin: pinmux_P9_25_qep_pin { + pinctrl-single,pins = <0x1ac 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_25_pruout_pin: pinmux_P9_25_pruout_pin { + pinctrl-single,pins = <0x1ac 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_25_pruin_pin: pinmux_P9_25_pruin_pin { + pinctrl-single,pins = <0x1ac 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_25_audio_pin: pinmux_P9_25_audio_pin { + pinctrl-single,pins = <0x1ac (PIN_INPUT_PULLUP | MUX_MODE0)>; }; /* mcasp0_ahclkx.mcasp0_ahclkx */ + + /* P9_26 (ZCZ ball D16) */ + P9_26_default_pin: pinmux_P9_26_default_pin { + pinctrl-single,pins = <0x180 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_26_gpio_pin: pinmux_P9_26_gpio_pin { + pinctrl-single,pins = <0x180 0x2F>; }; /* Mode 7, RxActive */ + P9_26_gpio_pu_pin: pinmux_P9_26_gpio_pu_pin { + pinctrl-single,pins = <0x180 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_26_gpio_pd_pin: pinmux_P9_26_gpio_pd_pin { + pinctrl-single,pins = <0x180 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_26_uart_pin: pinmux_P9_26_uart_pin { + pinctrl-single,pins = <0x180 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_26_can_pin: pinmux_P9_26_can_pin { + pinctrl-single,pins = <0x180 0x12>; }; /* Mode 2, Pull-Up, RxActive */ + P9_26_i2c_pin: pinmux_P9_26_i2c_pin { + pinctrl-single,pins = <0x180 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + P9_26_pruin_pin: pinmux_P9_26_pruin_pin { + pinctrl-single,pins = <0x180 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_27 (ZCZ ball C13) */ + P9_27_default_pin: pinmux_P9_27_default_pin { + pinctrl-single,pins = <0x1a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_27_gpio_pin: pinmux_P9_27_gpio_pin { + pinctrl-single,pins = <0x1a4 0x2F>; }; /* Mode 7, RxActive */ + P9_27_gpio_pu_pin: pinmux_P9_27_gpio_pu_pin { + pinctrl-single,pins = <0x1a4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_27_gpio_pd_pin: pinmux_P9_27_gpio_pd_pin { + pinctrl-single,pins = <0x1a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_27_qep_pin: pinmux_P9_27_qep_pin { + pinctrl-single,pins = <0x1a4 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_27_pruout_pin: pinmux_P9_27_pruout_pin { + pinctrl-single,pins = <0x1a4 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_27_pruin_pin: pinmux_P9_27_pruin_pin { + pinctrl-single,pins = <0x1a4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_28 (ZCZ ball C12) Audio */ + P9_28_default_pin: pinmux_P9_28_default_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_gpio_pin: pinmux_P9_28_gpio_pin { + pinctrl-single,pins = <0x19c 0x2F>; }; /* Mode 7, RxActive */ + P9_28_gpio_pu_pin: pinmux_P9_28_gpio_pu_pin { + pinctrl-single,pins = <0x19c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_28_gpio_pd_pin: pinmux_P9_28_gpio_pd_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_pwm_pin: pinmux_P9_28_pwm_pin { + pinctrl-single,pins = <0x19c 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_28_spi_pin: pinmux_P9_28_spi_pin { + pinctrl-single,pins = <0x19c 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_28_pwm2_pin: pinmux_P9_28_pwm2_pin { + pinctrl-single,pins = <0x19c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_28_pruout_pin: pinmux_P9_28_pruout_pin { + pinctrl-single,pins = <0x19c 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_28_pruin_pin: pinmux_P9_28_pruin_pin { + pinctrl-single,pins = <0x19c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_28_audio_pin: pinmux_P9_28_audio_pin { + pinctrl-single,pins = <0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)>; }; /* mcasp0_ahclkr.mcasp0_axr2 */ + + /* P9_29 (ZCZ ball B13) Audio */ + P9_29_default_pin: pinmux_P9_29_default_pin { + pinctrl-single,pins = <0x194 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_29_gpio_pin: pinmux_P9_29_gpio_pin { + pinctrl-single,pins = <0x194 0x2F>; }; /* Mode 7, RxActive */ + P9_29_gpio_pu_pin: pinmux_P9_29_gpio_pu_pin { + pinctrl-single,pins = <0x194 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_29_gpio_pd_pin: pinmux_P9_29_gpio_pd_pin { + pinctrl-single,pins = <0x194 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_29_pwm_pin: pinmux_P9_29_pwm_pin { + pinctrl-single,pins = <0x194 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_29_spi_pin: pinmux_P9_29_spi_pin { + pinctrl-single,pins = <0x194 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_29_pruout_pin: pinmux_P9_29_pruout_pin { + pinctrl-single,pins = <0x194 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_29_pruin_pin: pinmux_P9_29_pruin_pin { + pinctrl-single,pins = <0x194 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_29_audio_pin: pinmux_P9_29_audio_pin { + pinctrl-single,pins = <0x194 (PIN_OUTPUT_PULLUP | MUX_MODE0)>; }; /* mcasp0_fsx.mcasp0_fsx */ + + /* P9_30 (ZCZ ball D12) */ + P9_30_default_pin: pinmux_P9_30_default_pin { + pinctrl-single,pins = <0x198 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_30_gpio_pin: pinmux_P9_30_gpio_pin { + pinctrl-single,pins = <0x198 0x2F>; }; /* Mode 7, RxActive */ + P9_30_gpio_pu_pin: pinmux_P9_30_gpio_pu_pin { + pinctrl-single,pins = <0x198 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_30_gpio_pd_pin: pinmux_P9_30_gpio_pd_pin { + pinctrl-single,pins = <0x198 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_30_pwm_pin: pinmux_P9_30_pwm_pin { + pinctrl-single,pins = <0x198 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_30_spi_pin: pinmux_P9_30_spi_pin { + pinctrl-single,pins = <0x198 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_30_pruout_pin: pinmux_P9_30_pruout_pin { + pinctrl-single,pins = <0x198 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_30_pruin_pin: pinmux_P9_30_pruin_pin { + pinctrl-single,pins = <0x198 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_31 (ZCZ ball A13) Audio */ + P9_31_default_pin: pinmux_P9_31_default_pin { + pinctrl-single,pins = <0x190 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_31_gpio_pin: pinmux_P9_31_gpio_pin { + pinctrl-single,pins = <0x190 0x2F>; }; /* Mode 7, RxActive */ + P9_31_gpio_pu_pin: pinmux_P9_31_gpio_pu_pin { + pinctrl-single,pins = <0x190 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_31_gpio_pd_pin: pinmux_P9_31_gpio_pd_pin { + pinctrl-single,pins = <0x190 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_31_pwm_pin: pinmux_P9_31_pwm_pin { + pinctrl-single,pins = <0x190 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_31_spi_pin: pinmux_P9_31_spi_pin { + pinctrl-single,pins = <0x190 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_31_pruout_pin: pinmux_P9_31_pruout_pin { + pinctrl-single,pins = <0x190 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_31_pruin_pin: pinmux_P9_31_pruin_pin { + pinctrl-single,pins = <0x190 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_31_audio_pin: pinmux_P9_31_audio_pin { + pinctrl-single,pins = <0x190 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)>; }; /* mcasp0_aclkx.mcasp0_aclkx */ + + /* P9_32 VADC */ + /* P9_33 (ZCZ ball C8 ) AIN4 */ + /* P9_34 AGND */ + /* P9_35 (ZCZ ball A8 ) AIN6 */ + /* P9_36 (ZCZ ball B8 ) AIN5 */ + /* P9_37 (ZCZ ball B7 ) AIN2 */ + /* P9_38 (ZCZ ball A7 ) AIN3 */ + /* P9_39 (ZCZ ball B6 ) AIN0 */ + /* P9_40 (ZCZ ball C7 ) AIN1 */ + + /* P9_41 (ZCZ ball D14) */ + P9_41_default_pin: pinmux_P9_41_default_pin { + pinctrl-single,pins = <0x1b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_41_gpio_pin: pinmux_P9_41_gpio_pin { + pinctrl-single,pins = <0x1b4 0x2F>; }; /* Mode 7, RxActive */ + P9_41_gpio_pu_pin: pinmux_P9_41_gpio_pu_pin { + pinctrl-single,pins = <0x1b4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_41_gpio_pd_pin: pinmux_P9_41_gpio_pd_pin { + pinctrl-single,pins = <0x1b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_41_timer_pin: pinmux_P9_41_timer_pin { + pinctrl-single,pins = <0x1b4 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_41_pruin_pin: pinmux_P9_41_pruin_pin { + pinctrl-single,pins = <0x1b4 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) */ + P9_91_default_pin: pinmux_P9_91_default_pin { + pinctrl-single,pins = <0x1a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_91_gpio_pin: pinmux_P9_91_gpio_pin { + pinctrl-single,pins = <0x1a8 0x2F>; }; /* Mode 7, RxActive */ + P9_91_gpio_pu_pin: pinmux_P9_91_gpio_pu_pin { + pinctrl-single,pins = <0x1a8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_91_gpio_pd_pin: pinmux_P9_91_gpio_pd_pin { + pinctrl-single,pins = <0x1a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_91_qep_pin: pinmux_P9_91_qep_pin { + pinctrl-single,pins = <0x1a8 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_91_pruout_pin: pinmux_P9_91_pruout_pin { + pinctrl-single,pins = <0x1a8 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_91_pruin_pin: pinmux_P9_91_pruin_pin { + pinctrl-single,pins = <0x1a8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_42 (ZCZ ball C18) */ + P9_42_default_pin: pinmux_P9_42_default_pin { + pinctrl-single,pins = <0x164 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_42_gpio_pin: pinmux_P9_42_gpio_pin { + pinctrl-single,pins = <0x164 0x2F>; }; /* Mode 7, RxActive */ + P9_42_gpio_pu_pin: pinmux_P9_42_gpio_pu_pin { + pinctrl-single,pins = <0x164 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_42_gpio_pd_pin: pinmux_P9_42_gpio_pd_pin { + pinctrl-single,pins = <0x164 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_42_pwm_pin: pinmux_P9_42_pwm_pin { + pinctrl-single,pins = <0x164 0x20>; }; /* Mode 0, Pull-Down, RxActive */ + P9_42_uart_pin: pinmux_P9_42_uart_pin { + pinctrl-single,pins = <0x164 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_42_spics_pin: pinmux_P9_42_spics_pin { + pinctrl-single,pins = <0x164 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P9_42_spiclk_pin: pinmux_P9_42_spiclk_pin { + pinctrl-single,pins = <0x164 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) */ + P9_92_default_pin: pinmux_P9_92_default_pin { + pinctrl-single,pins = <0x1a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_92_gpio_pin: pinmux_P9_92_gpio_pin { + pinctrl-single,pins = <0x1a0 0x2F>; }; /* Mode 7, RxActive */ + P9_92_gpio_pu_pin: pinmux_P9_92_gpio_pu_pin { + pinctrl-single,pins = <0x1a0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_92_gpio_pd_pin: pinmux_P9_92_gpio_pd_pin { + pinctrl-single,pins = <0x1a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_92_qep_pin: pinmux_P9_92_qep_pin { + pinctrl-single,pins = <0x1a0 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_92_pruout_pin: pinmux_P9_92_pruout_pin { + pinctrl-single,pins = <0x1a0 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_92_pruin_pin: pinmux_P9_92_pruin_pin { + pinctrl-single,pins = <0x1a0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_43 GND */ + /* P9_44 GND */ + /* P9_45 GND */ + /* P9_46 GND */ +}; + +/**********************************************************************/ +/* Pin Multiplex Helpers */ +/* */ +/* These provide userspace runtime pin configuration for the */ +/* BeagleBone cape expansion headers */ +/**********************************************************************/ + +&ocp { + /************************/ + /* P8 Header */ + /************************/ + + P8_07_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_07_default_pin>; + pinctrl-1 = <&P8_07_gpio_pin>; + pinctrl-2 = <&P8_07_gpio_pu_pin>; + pinctrl-3 = <&P8_07_gpio_pd_pin>; + pinctrl-4 = <&P8_07_timer_pin>; + }; + + P8_08_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_08_default_pin>; + pinctrl-1 = <&P8_08_gpio_pin>; + pinctrl-2 = <&P8_08_gpio_pu_pin>; + pinctrl-3 = <&P8_08_gpio_pd_pin>; + pinctrl-4 = <&P8_08_timer_pin>; + }; + + P8_09_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_09_default_pin>; + pinctrl-1 = <&P8_09_gpio_pin>; + pinctrl-2 = <&P8_09_gpio_pu_pin>; + pinctrl-3 = <&P8_09_gpio_pd_pin>; + pinctrl-4 = <&P8_09_timer_pin>; + }; + + P8_10_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_10_default_pin>; + pinctrl-1 = <&P8_10_gpio_pin>; + pinctrl-2 = <&P8_10_gpio_pu_pin>; + pinctrl-3 = <&P8_10_gpio_pd_pin>; + pinctrl-4 = <&P8_10_timer_pin>; + }; + + P8_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "qep"; + pinctrl-0 = <&P8_11_default_pin>; + pinctrl-1 = <&P8_11_gpio_pin>; + pinctrl-2 = <&P8_11_gpio_pu_pin>; + pinctrl-3 = <&P8_11_gpio_pd_pin>; + pinctrl-4 = <&P8_11_pruout_pin>; + pinctrl-5 = <&P8_11_qep_pin>; + }; + + P8_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "qep"; + pinctrl-0 = <&P8_12_default_pin>; + pinctrl-1 = <&P8_12_gpio_pin>; + pinctrl-2 = <&P8_12_gpio_pu_pin>; + pinctrl-3 = <&P8_12_gpio_pd_pin>; + pinctrl-4 = <&P8_12_pruout_pin>; + pinctrl-5 = <&P8_12_qep_pin>; + }; + + P8_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_13_default_pin>; + pinctrl-1 = <&P8_13_gpio_pin>; + pinctrl-2 = <&P8_13_gpio_pu_pin>; + pinctrl-3 = <&P8_13_gpio_pd_pin>; + pinctrl-4 = <&P8_13_pwm_pin>; + }; + + P8_14_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_14_default_pin>; + pinctrl-1 = <&P8_14_gpio_pin>; + pinctrl-2 = <&P8_14_gpio_pu_pin>; + pinctrl-3 = <&P8_14_gpio_pd_pin>; + pinctrl-4 = <&P8_14_pwm_pin>; + }; + + P8_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruin", "qep"; + pinctrl-0 = <&P8_15_default_pin>; + pinctrl-1 = <&P8_15_gpio_pin>; + pinctrl-2 = <&P8_15_gpio_pu_pin>; + pinctrl-3 = <&P8_15_gpio_pd_pin>; + pinctrl-4 = <&P8_15_pruin_pin>; + pinctrl-5 = <&P8_15_qep_pin>; + }; + + P8_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruin", "qep"; + pinctrl-0 = <&P8_16_default_pin>; + pinctrl-1 = <&P8_16_gpio_pin>; + pinctrl-2 = <&P8_16_gpio_pu_pin>; + pinctrl-3 = <&P8_16_gpio_pd_pin>; + pinctrl-4 = <&P8_16_pruin_pin>; + pinctrl-5 = <&P8_16_qep_pin>; + }; + + P8_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_17_default_pin>; + pinctrl-1 = <&P8_17_gpio_pin>; + pinctrl-2 = <&P8_17_gpio_pu_pin>; + pinctrl-3 = <&P8_17_gpio_pd_pin>; + pinctrl-4 = <&P8_17_pwm_pin>; + }; + + P8_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&P8_18_default_pin>; + pinctrl-1 = <&P8_18_gpio_pin>; + pinctrl-2 = <&P8_18_gpio_pu_pin>; + pinctrl-3 = <&P8_18_gpio_pd_pin>; + }; + + P8_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_19_default_pin>; + pinctrl-1 = <&P8_19_gpio_pin>; + pinctrl-2 = <&P8_19_gpio_pu_pin>; + pinctrl-3 = <&P8_19_gpio_pd_pin>; + pinctrl-4 = <&P8_19_pwm_pin>; + }; + + P8_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&P8_26_default_pin>; + pinctrl-1 = <&P8_26_gpio_pin>; + pinctrl-2 = <&P8_26_gpio_pu_pin>; + pinctrl-3 = <&P8_26_gpio_pd_pin>; + }; + + P8_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_27_default_pin>; + pinctrl-1 = <&P8_27_gpio_pin>; + pinctrl-2 = <&P8_27_gpio_pu_pin>; + pinctrl-3 = <&P8_27_gpio_pd_pin>; + pinctrl-4 = <&P8_27_pruout_pin>; + pinctrl-5 = <&P8_27_pruin_pin>; + pinctrl-6 = <&P8_27_hdmi_pin>; + }; + + P8_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_28_default_pin>; + pinctrl-1 = <&P8_28_gpio_pin>; + pinctrl-2 = <&P8_28_gpio_pu_pin>; + pinctrl-3 = <&P8_28_gpio_pd_pin>; + pinctrl-4 = <&P8_28_pruout_pin>; + pinctrl-5 = <&P8_28_pruin_pin>; + pinctrl-6 = <&P8_28_hdmi_pin>; + }; + + P8_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_29_default_pin>; + pinctrl-1 = <&P8_29_gpio_pin>; + pinctrl-2 = <&P8_29_gpio_pu_pin>; + pinctrl-3 = <&P8_29_gpio_pd_pin>; + pinctrl-4 = <&P8_29_pruout_pin>; + pinctrl-5 = <&P8_29_pruin_pin>; + pinctrl-6 = <&P8_29_hdmi_pin>; + }; + + P8_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_30_default_pin>; + pinctrl-1 = <&P8_30_gpio_pin>; + pinctrl-2 = <&P8_30_gpio_pu_pin>; + pinctrl-3 = <&P8_30_gpio_pd_pin>; + pinctrl-4 = <&P8_30_pruout_pin>; + pinctrl-5 = <&P8_30_pruin_pin>; + pinctrl-6 = <&P8_30_hdmi_pin>; + }; + + P8_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","uart", "hdmi"; + pinctrl-0 = <&P8_31_default_pin>; + pinctrl-1 = <&P8_31_gpio_pin>; + pinctrl-2 = <&P8_31_gpio_pu_pin>; + pinctrl-3 = <&P8_31_gpio_pd_pin>; + pinctrl-4 = <&P8_31_uart_pin>; + pinctrl-5 = <&P8_31_hdmi_pin>; + }; + + P8_32_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "hdmi"; + pinctrl-0 = <&P8_32_default_pin>; + pinctrl-1 = <&P8_32_gpio_pin>; + pinctrl-2 = <&P8_32_gpio_pu_pin>; + pinctrl-3 = <&P8_32_gpio_pd_pin>; + pinctrl-4 = <&P8_32_hdmi_pin>; + }; + + P8_33_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "hdmi"; + pinctrl-0 = <&P8_33_default_pin>; + pinctrl-1 = <&P8_33_gpio_pin>; + pinctrl-2 = <&P8_33_gpio_pu_pin>; + pinctrl-3 = <&P8_33_gpio_pd_pin>; + pinctrl-4 = <&P8_33_hdmi_pin>; + }; + + P8_34_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","pwm", "hdmi"; + pinctrl-0 = <&P8_34_default_pin>; + pinctrl-1 = <&P8_34_gpio_pin>; + pinctrl-2 = <&P8_34_gpio_pu_pin>; + pinctrl-3 = <&P8_34_gpio_pd_pin>; + pinctrl-4 = <&P8_34_pwm_pin>; + pinctrl-5 = <&P8_34_hdmi_pin>; + }; + + P8_35_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "hdmi"; + pinctrl-0 = <&P8_35_default_pin>; + pinctrl-1 = <&P8_35_gpio_pin>; + pinctrl-2 = <&P8_35_gpio_pu_pin>; + pinctrl-3 = <&P8_35_gpio_pd_pin>; + pinctrl-4 = <&P8_35_hdmi_pin>; + }; + + P8_36_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","pwm", "hdmi"; + pinctrl-0 = <&P8_36_default_pin>; + pinctrl-1 = <&P8_36_gpio_pin>; + pinctrl-2 = <&P8_36_gpio_pu_pin>; + pinctrl-3 = <&P8_36_gpio_pd_pin>; + pinctrl-4 = <&P8_36_pwm_pin>; + pinctrl-5 = <&P8_36_hdmi_pin>; + }; + + P8_37_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","uart","pwm", "hdmi"; + pinctrl-0 = <&P8_37_default_pin>; + pinctrl-1 = <&P8_37_gpio_pin>; + pinctrl-2 = <&P8_37_gpio_pu_pin>; + pinctrl-3 = <&P8_37_gpio_pd_pin>; + pinctrl-4 = <&P8_37_uart_pin>; + pinctrl-5 = <&P8_37_pwm_pin>; + pinctrl-6 = <&P8_37_hdmi_pin>; + }; + + P8_38_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","uart","pwm", "hdmi"; + pinctrl-0 = <&P8_38_default_pin>; + pinctrl-1 = <&P8_38_gpio_pin>; + pinctrl-2 = <&P8_38_gpio_pu_pin>; + pinctrl-3 = <&P8_38_gpio_pd_pin>; + pinctrl-4 = <&P8_38_uart_pin>; + pinctrl-5 = <&P8_38_pwm_pin>; + pinctrl-6 = <&P8_38_hdmi_pin>; + }; + + P8_39_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_39_default_pin>; + pinctrl-1 = <&P8_39_gpio_pin>; + pinctrl-2 = <&P8_39_gpio_pu_pin>; + pinctrl-3 = <&P8_39_gpio_pd_pin>; + pinctrl-4 = <&P8_39_pruout_pin>; + pinctrl-5 = <&P8_39_pruin_pin>; + pinctrl-6 = <&P8_39_hdmi_pin>; + }; + + P8_40_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_40_default_pin>; + pinctrl-1 = <&P8_40_gpio_pin>; + pinctrl-2 = <&P8_40_gpio_pu_pin>; + pinctrl-3 = <&P8_40_gpio_pd_pin>; + pinctrl-4 = <&P8_40_pruout_pin>; + pinctrl-5 = <&P8_40_pruin_pin>; + pinctrl-6 = <&P8_40_hdmi_pin>; + }; + + P8_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_41_default_pin>; + pinctrl-1 = <&P8_41_gpio_pin>; + pinctrl-2 = <&P8_41_gpio_pu_pin>; + pinctrl-3 = <&P8_41_gpio_pd_pin>; + pinctrl-4 = <&P8_41_pruout_pin>; + pinctrl-5 = <&P8_41_pruin_pin>; + pinctrl-6 = <&P8_41_hdmi_pin>; + }; + + P8_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_42_default_pin>; + pinctrl-1 = <&P8_42_gpio_pin>; + pinctrl-2 = <&P8_42_gpio_pu_pin>; + pinctrl-3 = <&P8_42_gpio_pd_pin>; + pinctrl-4 = <&P8_42_pruout_pin>; + pinctrl-5 = <&P8_42_pruin_pin>; + pinctrl-6 = <&P8_42_hdmi_pin>; + }; + + P8_43_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_43_default_pin>; + pinctrl-1 = <&P8_43_gpio_pin>; + pinctrl-2 = <&P8_43_gpio_pu_pin>; + pinctrl-3 = <&P8_43_gpio_pd_pin>; + pinctrl-4 = <&P8_43_pruout_pin>; + pinctrl-5 = <&P8_43_pruin_pin>; + pinctrl-6 = <&P8_43_pwm_pin>; + pinctrl-7 = <&P8_43_hdmi_pin>; + }; + + P8_44_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_44_default_pin>; + pinctrl-1 = <&P8_44_gpio_pin>; + pinctrl-2 = <&P8_44_gpio_pu_pin>; + pinctrl-3 = <&P8_44_gpio_pd_pin>; + pinctrl-4 = <&P8_44_pruout_pin>; + pinctrl-5 = <&P8_44_pruin_pin>; + pinctrl-6 = <&P8_44_pwm_pin>; + pinctrl-7 = <&P8_44_hdmi_pin>; + }; + + P8_45_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_45_default_pin>; + pinctrl-1 = <&P8_45_gpio_pin>; + pinctrl-2 = <&P8_45_gpio_pu_pin>; + pinctrl-3 = <&P8_45_gpio_pd_pin>; + pinctrl-4 = <&P8_45_pruout_pin>; + pinctrl-5 = <&P8_45_pruin_pin>; + pinctrl-6 = <&P8_45_pwm_pin>; + pinctrl-7 = <&P8_45_hdmi_pin>; + }; + + P8_46_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_